欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

Sintering is the heating of a powder to a certain temperature for a certain period of time and then cooling the material to obtain a product of the desired properties. This whole process of the special heat treatment is called sintering.
Sintering enables porous powder compacts to become the product of a certain texture and properties. Although the attributes of the product are related to many factors prior to sintering, in many cases the sintering process have significant or even dominating influence on the organization and properties of the final product.
According to the classification principle of powder metallurgy on sintering, cemented carbide sintering belongs to the multi-phase liquid sintering. From the perspective of the process characteristics of the sintering process, the sintering of the cemented carbide may be by hydrogen protection, vacuum sintering, hot pressing sintering, hot isostatic pressing, and the like.

What is Sintering and Hot pressing? 1

Changes in sintered body during sintering

After the sintering of the cemented carbide compact, the most easily observed change is that the volume shrinkage of the compact block, the increased strength, and the surface of the alloy exhibits metallic luster. Typically, the compact has a porosity of about 50%, while the article should generally be less than 0.2%, which is nearly fully dense. Before sintering, the pressing block should also be handled lightly to avoid its damage in the production process.While the sintered products have the strength to withstand various working conditions.
Different from the powder forming process, the change of sinter properties indicates that there are qualitative changes between powder particles in the sintering process, which is that the bonding of alloy grains replaces the contact between powder particles that making the alloy form a solid whole body, thus forming excellent physical and mechanical properties.
Several stages of the sintering process
The cemented carbide sintering process can be divided into four basic stages.

1. Removal of forming agent and pre-burning stage (<800 °C)

In the first stage, the sintering hoop changes as follows:
1) Removal of the forming agent. At the initial stage of sintering, as the temperature increases, the forming agent gradually cracks (such as rubber) or vaporizes (such as paraffin) and excludes the sintered body. At the same time, the forming agent is more or less The sintered body is carbonized.
2) Powder surface oxide reduction. When sintered in hydrogen, hydrogen can reduce cobalt and tungsten oxides. When vacuum sintering, the reduction of carbon at this temperature is not strong.
3) The state of the powder particles changes with each other. At this temperature, the contact stress between the powder particles is gradually eliminated, the bonded metal powder begins to recover and recrystallize, the particles begin to diffuse on the surface, and the strength of the compact is improved.

What is Sintering and Hot pressing? 2

2. Solid phase sintering stage (800 ° C ~ eutectic temperature)

The eutectic temperature refers to a temperature at which a eutectic liquid phase starts to appear in the sintered body when the temperature is gradually raised, and for the WC-Co, the eutectic temperature at the time of equilibrium sintering is 1340%.
At the temperature before the liquid phase appears, in addition to the process that continues in the previous stage, some solid phase reactions in the sintered body are intensified, the diffusion speed is increased, and the plastic flow of the particles is strengthened, so that the sintered body exhibits significant shrinkage.

3. Liquid phase sintering stage (eutectic temperature ~ sintering temperature)

When the liquid phase of the sintered body appears, the shrinkage of the sintered body is completed quickly, and the carbide grains grow and form a skeleton, thereby laying the basic structure of the alloy.

4. Cooling stage (sintering temperature ~ room temperature)

At this stage, the microstructure and binder phase composition of the alloy change somewhat depending on the cooling conditions. After cooling, an alloy of the final microstructure is obtained.

About hot pressing

Hot pressing is a process in which pressing and sintering are simultaneously performed. In addition to the usual use of resistance heating and induction heating technology, there are also new processes and equipment such as vacuum hot pressing, vibration hot pressing, equalizing hot pressing, isostatic pressing.

What is Sintering and Hot pressing? 3

1. Densification mechanism of hot pressing process

The process in which the powder of the final addition agent is placed in a graphite stamper so that sintering and pressing are simultaneously performed is called hot pressing.
Although the hot pressing is performed simultaneously with the two processes of pressing and sintering, there is no principle difference from the ordinary cold press forming and sintering. From the viewpoint of the effect, the hot pressing greatly shortens the phase transition and the time for forming the alloy. Therefore, it can be said that the hot pressing process is an activated sintering process. The densification process of the alloys produced by the two production methods was compared. From the alloy density–sintering time curve, it can be seen that the sintering process takes 1-2 hours to complete, and it takes only 3 to 10 minutes for hot pressing.
The sintering process during hot pressing is a highly unbalanced process. When the mixture powder is continuously heated under pressure, the oxide film on the surface of the powder is broken under pressure and can be reduced by carbon. However, unlike the sintering process, the hot pressing does not have enough time to balance the solubility of WC in Co, and the recrystallization process through the liquid phase does not occur during the hot pressing process. Therefore, the shrinkage of the hot pressed product is different from ordinary Sintering method.
Besides,some studies have shown that the shrinkage of hot pressed products is caused by the flow process. Before the appearance of the liquid phase, it mainly relies on plastic flow. When the liquid phase appears, the re-alignment of the carbide particles under the action of pressure is also called the liquid phase flow, so that the compact is contracted. Since the hot pressing time is short, diffusion and recrystallization are difficult to carry out.
In addition to temperature and pressure promoting the shrinkage of the sintering process, the holding time also has an effect on the density of the hot pressed product. The higher the temperature, the greater the eye force, the more intense the shrinkage of the compact over time during the onset of hot pressing, and the shorter the time it takes for the density to almost completely cease to change. When a certain holding time is reached, the density of the briquettes will no longer continue to increase, and it will be meaningless to extend the holding time.
In addition, powders with crystal defects can achieve a larger alloy density because the presence of defects can activate the hot pressing process.

What is Sintering and Hot pressing? 4

2.the characteristics of hot pressing process

The hot pressing process gives its products a unique set of advantages. Therefore, this process plays a major role in the production of cemented carbide. The main feature of this process is.
a.The hot-pressed product has high density and good performance. The porosity of the hot-pressed product is extremely low, and the density almost reaches the theoretical value. At the same time, since the hot pressing time is short, the carbide grains do not grow due to the recrystallization process, so the product carbon is finer than the tungsten crystal grains, which makes the hot pressed product have higher hardness and better wear resistance, especially it is suitable for the manufacture of precision tools such as precision rolls and high-precision wear parts.
b.The pressing pressure is small, and it can produce large-scale products. The unit pressing pressure required for hot pressing is only about one tenth of the cold pressing. Moreover, the size of the product can be expanded by welding, and therefore, the size of the hot-pressed product is limited by the capacity of the press to be less than the cold pressure.
At present, the weight of cemented carbide products produced by hot pressing can reach several tens of kilograms or even hundreds of kilograms.
c.It can produce products with complicated shapes. Due to the hot pressing, the powder materials have thermoplasticity and good fluidity, so they can be made into shaped products with complicated shapes, such as thin-walled tubes and products such as ball cylinders. However, for long pieces, there is still a case where the density is uneven, and the welded long parts are often unevenly welded.
d. It can produce large-size and non-deformed products. The hot pressing method overcomes the shortcomings of cold-pressing and sintering deformation, and can obtain long pieces without bending and hollow products with relatively accurate dimensions. However, due to hot pressing, cobalt is extruded from the surface of the product, which not only causes cobalt loss (1 to 3%) but also makes the surface of the hot-pressed product rough, which is difficult to clean and process.
e. Suitable for single-piece production. Hot-pressing tools are easy to manufacture and have a short production cycle, so they are especially suitable for single-piece or small-volume production that is urgently needed.
f.Low productivity and high cost. The hot pressing method can only produce one to several products at a time. The mold cost is high and the service life is short. Therefore, it is not suitable for large-scale production. It is generally used for the production of cold-sintering method. product.
g. High operating technology is required. During the hot pressing process, the combination of temperature and pressure, temperature rise and cooling rate, and shrinkage control play a decisive role in product performance and defects. Therefore, the operator is required to have a high level of skill.
One thing is noteworthy is that the development of equilibrium hot pressing and isostatic hot pressing overcomes some of the shortcomings of the hot pressing process.

Schreibe einen Kommentar

Deine E-Mail-Adresse wird nicht ver?ffentlicht. Erforderliche Felder sind mit * markiert.

国产午夜精品理论片A级漫画-久久精品国产99亚洲精品| 亚洲欧美另类综合偷拍-婷婷社区综合在线观看| 韩漫一区二区在线观看-精品国产免费未成女一区二区三区| 日韩高清在线观看一区二区-美产av在线免费观看| 日本中文字幕啊啊啊啊-久久精品伊人久久精品伊人| 国产福利视频一区二区三区-日韩人妻中文视频精品| 国产一级片久久免费看同-麻豆精品尤物一区二区青青| 亚洲美女喘息呻吟的网站-国产免费一区二区三区三洲| 亚洲愉拍自拍欧美精品app-亚洲一区不卡在线视频| 精彩亚洲一区二区三区-中文字幕中文字幕在线色站| 一区二区三区日本韩国欧美-日本1区2区3区4区在线观看| 天天干天天天天天天天-亚洲综合av在线三区| 欧美精品国产白浆久久正在-国产精彩视频一区二区三区| 国内精产熟女自线一二三区-六月丁香婷婷在线观看| 亚洲欧美日韩二区三区-国产在线欧美一区日韩二区| 欧美日韩精品人妻在线-在线播放中文字幕一区| 亚洲av日韩五月天久热精品-国产日韩欧美一区二区三区群战| 欧美日韩精品人妻在线-在线播放中文字幕一区| 人妻少妇无乱码中文字幕-人成免费视频一区二区| 欧美看片一区二区三区-人妻无卡精品视频在线| 欧美日韩国产亚洲免费-肉体粗喘娇吟国产91| 在线国产自偷自拍视频-蜜桃a∨噜噜一区二区三区| 国产黄污网站在线观看-成人av电影中文字幕| av噜噜国产在线观看-欧美视频亚洲视频一区二区三区| 国产成人精品免费视频大全办公室-亚洲欧美日本综合在线| 欧美字幕一区二区三区-好吊妞欧美一区二区在线观看| 久久亚州天堂一区二区-色噜噜色哟哟一区二区三区| 日韩精品中文在线观看一区-亚洲bt欧美bt精品| 黑丝av少妇精品久久久久久久-中文字幕久久久人妻无码| 色综合色综合久久综合频道-埃及艳后黄版在线观看| 99久热精品免费观看四虎-亚洲天堂精品视频在线| 少妇一区二区三区粉嫩av-国产精品区久久久久久久| 久久夜色精品亚洲噜国产av-大香蕉伊人猫咪在线观看| 亚洲av成人一区国产精品网-国产偷_久久一级精品a免费| 黄片黄片在线免费观看-激情综合网激情五月俺也去| 天天日天天干天天综合-99久久综合狠狠综合久久| 日本女优一卡二卡在线观看-欧美大胆a级视频秒播| 可以免费看污污视频的网站-日韩欧美不卡视频在线观看| 99久久精品一区二区成人-麻豆国产av玩弄放荡人妇系列| 99热在线精品免费6-av一区二区在线观看| 激情字幕久久久字幕中文-一区二区三区免费黄片|