欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

鈦加工中的物理現(xiàn)象

The cutting force of titanium alloy is only slightly higher than that of steel with the same hardness, but the physical phenomenon of titanium alloy processing is much more complex than that of steel processing, which makes the titanium alloy processing face great difficulties.

為什么鈦是難加工材料? 2

Most titanium alloys have very low thermal conductivity, only 1 / 7 of steel and 1 / 16 of aluminum. Therefore, the heat generated in the process of cutting titanium alloy will not be transferred to the workpiece or taken away by the chips, but gathered in the cutting area, the generated temperature can be as high as 1000 ℃ or above, which makes the cutting edge of the tool wear, crack and generate chip tumor rapidly, and the worn cutting edge appears rapidly, which makes the cutting area generate more heat, further shortening the service life of the tool.

The high temperature produced in the cutting process destroys the surface integrity of titanium alloy parts at the same time, which leads to the decrease of geometric accuracy of parts and the phenomenon of work hardening that seriously reduces their fatigue strength.

The elasticity of titanium alloy may be beneficial to the performance of parts, but in the process of cutting, the elastic deformation of workpiece is an important reason for vibration. The cutting pressure makes the “elastic” workpiece leave the tool and rebound, so that the friction between the tool and the workpiece is greater than the cutting effect. The friction process also produces heat, which aggravates the problem of poor thermal conductivity of titanium alloy.

When machining thin-walled or ring shaped parts, this problem is more serious. It is not easy to process titanium alloy thin-walled parts to the expected dimensional accuracy. Because when the workpiece material is pushed away by the cutter, the local deformation of the thin wall has exceeded the elastic range, resulting in plastic deformation, and the material strength and hardness of the cutting point increase significantly. At this time, according to the originally determined cutting speed, the machining becomes too high, which further leads to sharp tool wear.

為什么鈦是難加工材料? 3

“Heat” is the “culprit” of titanium alloy difficult to process!

Technological know-how of titanium alloy processing

On the basis of understanding the processing mechanism of titanium alloy and previous experience, the main know-how of processing titanium alloy is as follows:

(1) The blade with positive angle geometry is used to reduce cutting force, cutting heat and workpiece deformation.

(2) Keep constant feeding to avoid hardening of workpiece. During the cutting process, the tool should always be in the feeding state. The radial cutting amount AE should be 30% of the radius.

(3) High pressure and large flow cutting fluid are used to ensure the thermal stability of the machining process and prevent the surface degeneration and tool damage due to the high temperature.

(4) Keeping the blade edge sharp and blunt is the cause of heat accumulation and wear, which is easy to lead to tool failure.

(5) It can be processed in the softest state of titanium alloy as much as possible, because the material becomes more difficult to process after hardening, heat treatment improves the strength of the material and increases the wear of the blade.

(6) Use large tip radius or chamfer to cut in, and try to put more blades into cutting.  This can reduce the cutting force and heat at each point and prevent local damage. In the milling of titanium alloy, the cutting speed has the greatest influence on the tool life VC, followed by the radial cut (milling depth) AE.

為什么鈦是難加工材料? 4

Starting from blade to solve the problem of titanium processing

The groove wear of the blade in titanium alloy machining is the local wear of the back and front along the cutting depth direction, which is often caused by the hardening layer left by the previous machining. The chemical reaction and diffusion of cutting tool and workpiece material at the processing temperature over 800 ℃ is also one of the reasons for the formation of groove wear. Because in the process of machining, titanium molecules of the workpiece accumulate in front of the blade, and “weld” to the blade under high pressure and high temperature, forming chip accretion tumor. When the chip accretion is peeled from the blade, the cemented carbide coating of the blade is taken away. Therefore, special blade material and geometry are required for titanium alloy processing.

Tool structure suitable for titanium machining

The focus of titanium alloy machining is heat. A large amount of high-pressure cutting fluid should be sprayed on the cutting edge timely and accurately to remove the heat quickly. There is a unique structure of milling cutter specially used for titanium alloy processing on the market.

色欲色欲色视频综合| 九九视频这里只有精品| 熟妇丰满大阴户熟妇啪啪| 国产剧情使劲操我逼| 激情久久久久久久久久久| 咪咪爱一级特黄大片| 欧美日本大白屁股大黑逼操逼视频| 白虎美女被大基吧操| 骚逼被狂插视频教程| 蜜臀av一区二区三区免费观| 骚货 淫水 国产| 黑丝美女被操到高潮| 日本美女阴户射尿| 男人添女人下面免費视頻| 国产精品无码毛片久久久| 色逼色逼色逼色逼色逼色| 欧洲美熟女乱又伦| 日韩亚洲AV无码一区二区不卡| 鸡巴操美女小穴羞羞视频| 熟女菊蕾老妇俱乐部视频| 国产亚洲精品高清视频免费| 色婷婷五月综合久久| 火辣美女的操大逼| 无码人妻免费一区二区三区| 欧美一区二区三区男人的天堂| 国产成人无码91精品一区| 欧美精品第一区二区三区| 五月天婷婷一区二区三区久久| 韩国无遮挡成人免费视频| 久久久中文字幕在线视频| 国产精品久久一区二区三区动| 午夜精品福利一区二区三区蜜桃p| 啊灬啊别停灬用力啊男男在线观看| 欧美在线A片一区二区三区| 亚洲综合网伊人中文| 最新的亚洲欧美中文字幕| 女人被躁到高潮嗷嗷叫小| 日韩精品一区二区天堂| 亚洲欧美一区二区三区在| 国精品午夜福利视频导航| 大波美女被插的好爽|