欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

The cutting fluid used in machining has two functions:

1. Cooling effect

2. Lubrication

Common cutting fluids are generally divided into two categories due to different emphasis surfaces:

One is aqueous solution mainly cooling:

The other is mainly lubricating oil.

Why is cutting fluid as same important as cutting tools in machining? 1

The cooling based aqueous solution is generally an emulsion like milk seen in the factory. It is used for rough machining in order to increase the cooling effect and improve the service life of tools.

Lubricating oil, such as oil for full loss system, kerosene, oleic acid and rapeseed oil, is used to increase the lubrication effect, ensure the surface roughness of the machined surface and reduce tool wear.

Cutting fluid can be used at high speed and low speed. Oil for full loss system is a cutting fluid used at low speed.

For example, in manual tapping, the oil used in the full loss system is used as the cutting fluid. It should be noted that when using oil for full loss system, if the temperature is higher than 250 ℃, its cooling and lubrication effect is not as good as that of water.

The cutting of machine tools is carried out under high temperature and high pressure on many occasions. Under high temperature and high pressure, cutting fluid containing extreme pressure agent should be used. So what is extreme pressure agent? Extreme pressure agent is a substance that can maintain lubrication under high temperature and high pressure.

General extreme pressure agents include sulfur, chlorine, molybdenum disulfide, oleic acid, graphite, etc. When extreme pressure agent is added to the cutting fluid, it is the cutting fluid used at high temperature.

Why is cutting fluid as same important as cutting tools in machining? 2

The current machining situation in the world is that the understanding of the role of cutting fluid is not high enough, and the role of cutting fluid is not fully utilized. In many machining occasions, the role of cutting fluid is the same as that of cutting tools, which is equally important. It is impossible to leave any one.

In terms of cooling, the current situation is: when machining parts in NC milling center and NC machining center, the flow of cutting fluid is much larger than that of ordinary lathe, and the large flow takes away a lot of heat, so as to make the cooling environment of the tool much better and make the tool have a high speed.

The flow of cutting fluid used in ordinary lathe is relatively small and the cooling environment is relatively poor. It can only run at a lower speed for cutting. If a large flow of cutting fluid is used for cooling on an ordinary lathe, it will cause splashing of cutting fluid and become generally not used.

Why is cutting fluid as same important as cutting tools in machining? 3

In terms of lubrication, many processors generally do not pay attention to the role of cutting fluid, but blindly pay attention to the role of cutting tools, pay more attention to the cutting angle of cutting tools, and do not pay attention to the cooling and lubrication during cutting, resulting in the wear of the used tools in a very short time, and the number of repeated grinding increases, so that the tools will be worn and scrapped in a short time.Why is cutting fluid as same important as cutting tools in machining? 4

發表評論

電子郵件地址不會被公開。 必填項已用*標注

国产一级第一级毛片| 色老头av亚洲三区三区| 日本成人精品一区二区三区| 翘臀小穴在线观看| 久久久精品亚洲Av| 日本熟妇一区二区三区四区| 日本熟妇一区二区三区四区| 大鸡巴干浪穴视频| 爱男爽高潮鸡穴视频| 午夜福利国产三级片| 少妇勾搭外卖员在线观看| 欧美巨屌虐无毛骚逼| 操我骚逼抽插视频| 国产中文字幕在线一区二区三区| 欧美日韩欧美国产中文字幕| 最新的精品亚洲一区二区| 新视觉亚洲三区二区一区理伦| 非洲人粗大长硬配种视频| 天天摸天天添人人澡| 精品精品国产一区二区性色av| 大鸡巴抽插小穴色虐视频| 又大黄又硬又爽免费视频| 亚洲国产综合精品 在线 一区| 91偷自产一区二区三区蜜臀| 激情五月六月婷婷俺来也| 国产成人亚洲欧美久久| 泡芙啪啪啪黄色污污| 国产精品视频一区二区三区八戒| 女人张开腿让男人捅个爽| 美女肏肏逼应用下载| 冷色系的发色有哪些颜色| 女人张开腿让男人捅个爽| 黄色片视频1024| 国产一区二区三区午夜精品久久| 欧美尤物操逼毛茸茸真爽| 无码爆一二三区免费视频| 日韩中文字幕一区二区高清| 亚洲欧洲综合成人综合网| 狠狠色伊人亚洲综合成人| 亚洲女同一区二区三久久精品| 尤物AV无码国产在线看|