欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

In the bearing and standard parts industry, steel balls and screws are produced using highly efficient automatic cold heading machines. These machines have high production rates, but for medium and large-sized steel balls, the life and efficiency of the matching alloy steel dies are reduced due to the following factors during the cold heading process:

Wear and deformation caused by the intense flow of the deformed metal on the die surface. Sometimes, the die cavity surface is scratched, abraded, or even adhered to, which easily causes dimensional errors and scrapping of the die, resulting in poor product quality.

The die cavity is easily deformed due to the relatively insufficient yield strength of the matrix material.

After continuous and repeated stress, especially in areas with stress concentration, the fatigue life of the alloy steel is relatively low, leading to fatigue failure as the number of heading operations increases.

Therefore, in addition to further improving the life of alloy steel dies, there is a widespread demand for a new material that is both wear-resistant and has good toughness to adapt to the development of the cold heading industry.

Test Results and Application Assessment

To expand the application field of cemented carbide and meet the urgent demand of steel ball factories for large-sized steel ball cemented carbide dies, based on our long-term work experience and domestic and foreign data collection, we finally selected a specially made coarse-grained WC powder, supplemented by an appropriate binder phase, to formulate YGC-I and YGC-Ⅱ coarse-grained cemented carbides (YGC-Ⅱ has a higher binder phase content than YGC-I). The conventional performance data of YGC-I and YGC-Ⅱ are shown in Table 1.

An Application of Coarse-Grained Cemented Carbide in Cold Heading Dies for Steel Balls 2

To study the effect of different particle sizes of WC powder on the fracture toughness of cemented carbide, fine-grained cemented carbide YG10X, medium-coarse grained cemented carbide YG18C, and YG20C were also prepared.

The fracture toughness of fine-grained, medium-coarse grained, and super-coarse grained cemented carbides with three different WC particle sizes was measured, and the results are shown in Table 2. It can be observed from Table 2 that as the WC particle size changes from fine-grained to medium-coarse grained and then to coarse grained, the fracture toughness of the alloy increases significantly, or even doubles. Even within the same particle size range, the fracture toughness of the alloy also increases with the increase of the binder phase content. This indicates that there are two ways to improve the fracture toughness of the alloy: first, by selecting coarse-grained WC powder, and second, by increasing the binder phase content of the alloy.

An Application of Coarse-Grained Cemented Carbide in Cold Heading Dies for Steel Balls 3

carbide material for cold heading

Selected YGC-I and YG10X samples were used to take scanning electron microscopy (SEM) fracture photos. Figure 1a shows the SEM fracture photo of YGC-I, and Figure 1b shows the SEM fracture photo of YG10X. Careful observation of the SEM fracture photos reveals that YGC-I has coarse grains and a thick binder phase layer, with cracks extending along the binder phase, resulting in mostly intergranular fractures and thus a higher fracture toughness K?C. In contrast, YG10X has very fine grains and a very thin binder phase layer, with mostly transgranular fractures, leading to a lower fracture toughness K?C. This indicates that the trend in fracture toughness values of carbides with different grain sizes is consistent with the conclusions drawn from the analysis of SEM fracture photos.

The aforementioned coarse-grained cemented carbide developed was applied to cold heading larger specification steel balls φ17.4625 and φ19.05. After being used on a Z32-28 machine at a certain factory, the usage data show that the coarse-grained cemented carbide is capable of stamping larger specification steel balls, and its die core life is more than 8 to 10 times longer than that of GCr15. This not only expands the application scope of cemented carbide but also provides the possibility for the bearing industry and standard parts industry to adopt carbide dies with larger heading forces. Moreover, due to the significant increase in die life, it brings about considerable economic benefits.

結(jié)論

1.Selecting specially made coarse-grained WC powder and correspondingly increasing the binder phase content of the alloy is an effective way to improve the fracture toughness of cemented carbide.

2.SEM fracture analysis indicates that coarse-grained cemented carbide fractures are mostly intergranular, resulting in a higher fracture toughness K?C, while fine-grained cemented carbide fractures are mostly transgranular, leading to a lower fracture toughness K?C.

3.The usage results show that the life of coarse-grained cemented carbide die cores is more than 8 to 10 times longer than that of GCr15.

4.In summary, for the stamping of larger specification steel balls, choosing coarse-grained cemented carbide is a reasonable option.

發(fā)表評論

電子郵件地址不會被公開。 必填項已用*標(biāo)注

亚洲大尺度无码无码专线一区| 国产乱理伦片在线观看夜| 大阴茎交于大阴户黄片视频| 麻豆91精品96久久久| 国产精品久久一区二区三区夜色| 被医生添奶头和下面好爽| 欧美十八一区二区三区| 国产精品亚洲一区二区三区极品| 欧美va精品亚洲va精品| 大阴茎交于大阴户黄片视频| 久久久五月性色视频| 日本欧美一区二区三区| 美女大骚逼幸福遍穴| 欧洲老妇人操大逼| 亚洲欧洲综合成人综合网| 亚洲免费福利视频| 青春草在线视频观看| 日韩欧美一区二三区风间由美| AV无码超清破解版流出| 中日韩国内精品视频| 亚洲男性天堂一区二区三区| 99爱这里只有精品| 精品福利一区二区三区在线观看| 久久精品小视频/| 中文字幕人妻一区二区三区人妻| 野外日逼视频免费看| 公交车上被后入搞逼漫画| 操国产骚逼逼逼逼逼逼逼| 亚洲一区二区三成人精品| 亚洲国产精品一区亚洲国产| 人妻夜夜添夜夜无码AV| 无码中文字幕免费一区二区三区| 校花内射国产麻豆欧美一区| 美女操逼视频app| 国产老妇伦国产熟女91| 成人高清在线播放一区二区三区| 黄色亚洲一级大片| 国产一区二区三区免费观在线| 国产a一级毛片午夜剧院| 任你橹在线久久精品9| 非洲人粗大长硬配种视频|