欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

CNC drilling machines and carbide micro drills have always been the mainstream equipment for processing PCB circuit boards. A large amount of PCB processing tasks still rely on CNC milling and drilling to complete. As a subsystem of electronic products, PCB circuit boards play a role as a core module unit. Modern high-performance electronic products have increasingly higher requirements for PCBs, which also means that the precision requirements for carbide micro drill are becoming higher and higher.

 

Common PCB substrate copper laminates are made by bonding the insulation material and copper foil using adhesive and hot pressing, with epoxy glass fiber cloth board used as a pressure plate reinforcement material.? The board contains uncured resin, and the heat generated by mechanical friction during processing will soften the uncured resin, increasing frictional resistance, breaking cutting tools, and producing sludge, which affects processing quality. This makes the mechanical processing performance of PCB boards relatively poor.

This article mainly compares and studies the cutting performance of carbide ?drills produced by our company in China and similar famous carbide ?drills abroad when processing PCB boards.

 

Test Conditions

The test selected drills of the same specifications but from different manufacturers to drill holes in PCB boards. The selected tool specifications are shown in Table 1.

carbide micro drill bit

To reduce the impact of experimental errors, four tools from two companies were selected for drilling experiments. The material being cut was a double-layer copper PCB with a thickness of 1.2mm, and a 2.5mm thick cardboard was placed underneath the work piece.

During the processing, the cutting performance of the tools from the two companies was compared by comparing the roughness and chip removal of the processed PCB board, as well as the tool life.

 

 

Experimental Data

Test PCB Machining Quality

The machining quality of the PCB boards observed after cutting with 8 different drill bits is shown in Table 2. It can be seen that the 4 drill bits from Meetyou company can generally achieve good machining results, except for the fourth bit which caused sawtooth-like defects on the PCB board. In comparison, two of the foreign company’s drill bits caused corrugated defects and sawtooth-like defects on the PCB board. The surface roughness of the PCB board after machining can also indicate that the micro drill from Meetyou company have better surface roughness during the machining process, while the drill bits from the foreign company have poorer surface roughness on the PCB board after machining. However, compared with the drill bits from Meetyou company, the chip removal effect of the drill bits from the foreign company is not as good.

5 Common Machining Quality Issues of carbide?micro drill on?PCB? 2

PCB Carbide micro drill’s service life

The average service life of 8 drill bits from Company 2 can be seen from Figure 3. It can be seen that the service life of Meetyou Company’s drill bits is about 40% higher than that of the drill bits from a foreign company.

5 Common Machining Quality Issues of carbide?micro drill on?PCB? 3

 

From Table 4, it can be seen that the lifespan values of the eight drills from the two companies are in a discrete distribution, with almost 40% difference in the lifespan of the same company’s drills. This shows that even though Meetyou’s drills have better quality, from the experiment we can see that there is still much room for improvement in the tungsten carbide micro drills of both companies.

5 Common Machining Quality Issues of carbide?micro drill on?PCB? 4

 

The experimental results showed that the surface roughness and tool life of the PCB board processed by Meetyou’s drill bit were better than those of the foreign company, but the tool life of both companies was not consistent. The photographs of the tools after processing showed that the main forms of tool wear were caused by the generation of abrasive particles and surface oxidation wear.

 

Problems Generated by carbide micro drill on?PCB Circuit Boards

Through high-speed photography to observe the drilling process and the chip removal situation, scanning electron microscopy to observe the drilling morphology, and using software such as Deform and AdvantEdge FEM to simulate the drilling process extensively, it was found that the drilling process of PCB circuit boards is not simply punching holes, but a conventional metal cutting process. It will form conical spiral chips, and the copper chips will bend and break under the action of gravity during the discharge process, and finally be thrown out at high speed rotation of the micro drill, as shown in Pic. 1.

The epoxy resin glass fiber cloth chips are discharged in the form of white powder. The resin in the chips is easy to soften under heating conditions, and the glass fiber chips are adhered together to form mixed chips, as shown in Pic. 2. This kind of mixed chips are easy to adhere to the hole wall and form drilling dirt, which will also adhere to the drill tip and affect the next drilling step, and may even adhere to the spiral groove surface to obstruct chip removal. The drilling models of micro drilling for copper foil and epoxy glass fiber cloth are shown in Pic.3.

5 Common Machining Quality Issues of carbide?micro drill on?PCB? 5

5 Common Machining Quality Issues of carbide?micro drill on?PCB? 6

 

Reasons analysis to cause drilling problems on PCB

Drilling force

The drilling force fluctuated significantly during the drilling of epoxy glass fiber cloth with micro-drills, which was due to the small size of the micro-drills. When drilling glass fibers, the axial drilling force decreased sharply with the fracture of the glass fibers because the micro-drill only drilled a few glass fibers at the same time. The axial force and torque both decreased with increasing speed, but increased with increasing feed rate and core thickness. With an increase in helix angle, the axial force increased, while the torque decreased. The typical drilling process of a micro-drill with a diameter of 0.1mm is shown in Figure 4.

5 Common Machining Quality Issues of carbide?micro drill on?PCB? 7

Drilling temperature

The temperature at the moment of drilling a PCB with micro-drills was measured using an infrared thermal imager and extensively simulated. The results showed that the drilling temperature was typically below 80°C at the moment of drilling with micro-drills. The drilling temperature decreased with an increase in feed rate and spindle speed, but increased with an increase in the number of drill holes and the diameter of the micro-drill. The drilling temperature measured by the infrared thermal imager is shown in Figure 5.

5 Common Machining Quality Issues of carbide?micro drill on?PCB? 8

Drill bit wear

the morphology of micro-drill wear was observed through scanning electron microscopy, as shown in Figure 6. The wear characteristics of micro-drills are mainly abrasive wear and adhesive wear. Abrasive wear mainly occurs on the transverse edge and main cutting edge, affecting the service life of micro-drills. Glass fibers and fillers in PCBs are the main cause of abrasive wear in micro-drills. Resin-mixed chip adhesion wear occurs on the drill tip and helix groove surface of micro-drills, as shown in Figure 7, which affects the cutting performance and chip removal of micro-drills, thereby causing the temperature inside the hole to accumulate and aggravating micro-drill wear.

5 Các v?n ?? v? ch?t l??ng gia c?ng ph? bi?n c?a máy khoan siêu nh? cacbua trên PCB? 9

  1. D=0.1 mm,vf=150cm/min,n=295/min,vr=2300cm/min,2500holes.
  2. D=0.2mm,vf=150cm/min,n=155/min,vr=1800cm/min,1500holes.
  3. D=0.3mm,vf=240cm/min,n=145/min,vr=1800cm/min,1500 holes

Fracture

It?was found that the fracture was caused by the edge near the drill tip participating in cutting during processing, which is easily damaged by friction and impact of glass fiber, causing cutting to not proceed normally. Micro-drill bending and severe twisting ultimately lead to micro-drill breakage. Experimental and simulation results show that excessive twisting load is the main cause of micro-drill breakage, and the fracture point of the micro-drill is located at the root of the micro-drill spiral groove, at a certain distance from the top of the drill.

Conclusion?of carbide micro-drill’s drilling quality for PCB.

In summary, by observing the micro-hole sections under scanning electron microscopy, it was found that not only are there entrance and exit burr problems on the micro-hole surface, but also entrance roundness error, entrance size error, burrs and hole position accuracy, and roughness of the hole wall. The burrs and edges of micro-drills are mainly caused by micro-drill wear. Roughness of the micro-hole wall mainly occurs due to the fracture and shedding of multiple glass fibers in the epoxy glass fiber layer. Hole position accuracy is mainly related to spindle vibration characteristics, drill diameter, and drill wear. Reducing feed speed and increasing rotation speed can improve the quality of micro-holes in PCBs within a certain number of drilling holes. The most fundamental method to improve micro-hole quality is to reduce the contact area between micro-drills and PCBs to improve the wear resistance of micro-drills.

Tr? l?i

Email c?a b?n s? kh?ng ???c hi?n th? c?ng khai. Các tr??ng b?t bu?c ???c ?ánh d?u *

可以免费看黄的香蕉视频| 男人的天堂久久久久久久| 骚逼被操视频拳交| 久久精品欧美精品免费观看| 亚洲男人的天堂2021| 鸡巴插进女人的逼里| 欧美高清一二三区| 熟妇好大好深好爽| 欧美国产综合日韩一区二区| 美女操逼视频app| 亚洲精品伦理熟女国产| 大黑屌爆操日本女人| 美国女人抠插bbb| 视频一区二区三区日韩视频| 精品久久久久五月婷五月| 三级无码日B视频| 尤物AV无码国产在线看| 69国产精品久久久久久人| 99国产精品一区二区| 骚逼毛茸茸乱伦视频| 视频一区视频二区制服丝袜| 欧美国产人妖另类色视频| 久久精品欧美日韩精品不卡| 国产成人AV一区二区在线观看| 日本免费暖暖在线小视频| 欧美日韩一级视频| 操的我的逼逼好爽好多水| 欲色欲香天天网综合久久| av人摸人人人澡人人超| 男生鸡鸡插进女生笑穴里| 国产精品碰碰现在自| 操的我的逼逼好爽好多水| 男人的天堂久久久久久久| 日韩视频在线网页| 免费看女人操逼玩| 性色av一区二区三区天美传媒四| 国产伦精品一区二区三区视频抖音| 大吊肏子宫在线观看| 国内精品久久久久精品97| 国产午夜爽爽爽男女免费动漫AV| 亚洲欧美一区二区三区孕妇|