欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

Milling process is essentially a kind of intermittent processing process. This causes the temperature at the cutting edge to fluctuate between high temperature (about 1000 ℃) and low temperature.

Effect of cutting fluid

When the cutting edge cuts in and cuts out, the temperature change will increase. As a result, the cutting edge is subject to thermal shock and periodic stresses, which may result in cracks and, in the worst case, premature end of tool life.

The higher the temperature of the cutting area, the less suitable the cutting fluid is.

In the finishing process, the use of cutting fluid will not shorten the tool life as much as in rough machining due to the reduced heat generated.

When to Use Wet Milling or Dry Milling? 2
Hot cracks on cutting edge

dry milling

Dry milling can prolong the life of cutting edge. The temperature does change, but it will remain within the design range of cemented carbide materials.

Rough milling should always be carried out without cutting fluid.

wet milling with cutting fluid

There are some exceptions to the use of cutting fluid:

1) Finish machining of stainless steel and aluminum alloys – used to prevent metal particles from sticking to the surface structure

2) Milling superalloys at low cutting speeds – for lubrication and cooling of parts

3) Cast iron milling, used to wet and remove dust to protect the environment and health and ensure the accuracy of parts

4) Milling of thin wall parts to prevent geometric deformation

5) When machining deep cavity, micro lubrication system (i.e. compressed air containing a small amount of special oil) can be used to assist chip removal

When to Use Wet Milling or Dry Milling? 3
Use compressed air and oil mist

In the micro lubrication system, the “oil mist” is only a few milliliters of oil per hour, and is discharged through the ordinary filtering ventilation system.

When to Use Wet Milling or Dry Milling? 4
Use a large flow of internal and external coolant

If wet milling must be carried out, a sufficient amount of cutting fluid should be used.

亚洲国产日韩欧美高清片| 我要操日本女人的逼| 国产精品毛片无遮挡高清| 国产一区曰韩二区欧美三区| 精品一区二区av天堂色偷偷| 爆乳喷奶水无码正在播放| 黑人猛操日本美女| 日本一二区视频在线观看| 九九在线精品亚洲国产| 这里只有久久精品| 美女裸胸屁股视频| 久久久国产精品2020| 欧美成人3p视频| 男人的天堂日本在线观看| 亚洲日韩国产欧美久久久| 怎么样操女人的逼亚洲Av黄片段| 鸡巴插骚逼真舒服| 国产a一级毛片午夜剧院| 天美传媒精品1区2区3区| 大香蕉中码手机在线视频| 成人精品视频区一区二区三| 国产伦精品一区二区三区视频抖音| 少妇毛片一区二区三区免费视频| 亚洲国际精品一区二区| 欧美一区二区三区色婷婷月色| 欧美日韩国产这里只有精品| 免费人成再在线观看| 男生用鸡巴操女生的视频| 西瓜在线看免费观看视频| 大鸡巴干浪穴视频| 综合伊人久久在一二三区| 国产天堂网一区二区三区 | 欧美一级淫片免费播放口| 日本高清一区二区三区在线观看| 日韩精品人妻一区二区免费| 久久国产亚洲高清| 国产精品999午夜激情| 日韩免费一级a毛片在线播放一级| 久久噜噜噜久久熟女精品| 久久亚洲精品无码AV宋| 亚洲国产成人手机版|