欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

When it comes to cutting chips, everyone is familiar. Experienced production personnel can infer the capacity and primary machining types of a machine shop based on the quantity and shape of chips produced. Optimizing chip control is a crucial topic in tool machining. Today, we will provide a simple analysis of chips and common methods for optimizing chip control.

Effective cutting chip control should avoid causing damage to the workpiece, tools, and operators; prevent production interruptions; and eliminate chip disposal issues.

5 Methods of Optimizing Cutting Chip Control between Cost and Efficiency 2

What factors affect chip formation?

Good chip formation can produce spiral short chips, which are generally believed to ensure longer tool life, easier chip handling and disposal, higher surface quality of machined parts, and a stable, reliable, and efficient cutting process. Simply put, ideal chips should be of a manageable size and require minimal effort during their formation.

In practice, numerous factors influence chip formation, including the shape of the tool, cutting conditions, material of the part, and cooling method.

Factors related to part material include the hardness and tensile strength of the workpiece, ductility, and structural considerations. These factors cannot be modified, but their impact on cutting chip formation must be considered.

The influence of the cooling system on chip formation is quite variable. Key tool characteristics include rake angle, cutting edge angle, tool nose radius, and the geometry of the cutting edge and chip breaker groove. Larger rake angles, lower cutting edge angles, and larger tool nose radii tend to produce longer chips. The effect of the coating type on chip formation is not easily defined.

Cutting conditions can intuitively affect chip formation, and altering these conditions is both easy and effective. The primary cutting condition to adjust is the chip thickness ratio or aspect ratio. When the chip thickness ratio is too low, so-called square cutting chips are produced, which impose excessive load on the tool tip, significantly limiting tool life. An excessively high chip thickness ratio results in long, ribbon-like cutting chips that are difficult to break into shorter pieces.

The chip thickness ratio is defined as the cutting width divided by the chip thickness. For a given feed rate, the cutting depth should be sufficiently large to avoid excessively low or high chip thickness ratios. Small cutting depths combined with certain feed rates produce square chips. Conversely, excessively small feed rates can lead to unbreakable ribbon-like chips.

In practical operations, cutting depth is usually fixed. In this case, the feed rate becomes crucial for good chip formation. Avoiding excessively low feed rates prevents long ribbon-like chips, while avoiding excessively high feed rates prevents the formation of square chips.

 

Chip Morphology

Cutting chips can be defined into four different types based on their cross-section:

Serrated, segmented, or discontinuous chips

Serrated or segmented cutting chips, also known as discontinuous chips, are semi-continuous chips with large areas of low shear strain and localized, small areas of high shear strain. This type of chip is commonly observed when machining materials with low thermal conductivity and strong strain-hardening characteristics. For example, when machining materials like titanium, the strength of the material increases under stress, especially under the combined effects of high temperature and stress. The appearance of these cutting chips is characterized by a serrated pattern.

Continuous cutting chips

Continuous chips are typically produced when machining ductile materials, such as low-carbon steel, copper, and aluminum alloys. Continuous cutting chips are difficult to handle and dispose of, as they can form very long spirals or coils around the workpiece and tool, posing a potential hazard to operators when they break. The prolonged contact time with the tool surface generates more frictional heat. Using chip breakers can effectively address this issue.

Built-up edge chips

When small particles of the workpiece material adhere to the cutting edge of the tool, a so-called built-up edge (BUE) is formed. This primarily occurs with soft and ductile workpiece materials, especially when forming continuous cutting chips. BUE can affect the cutting performance of the tool. These accumulations are very hard and brittle, and as layers of material build up, their stability decreases. When the BUE eventually breaks off, part of it is carried away with the chips to the tool surface, while another part remains on the machined surface, increasing surface roughness.

By increasing the cutting speed, using tools with a positive rake angle and sharper edges, applying coolant, and selecting cutting materials with lower chemical affinity to the workpiece material, the formation of BUE can be effectively reduced.

Shear chips

Shear chips or short chips, also known as discontinuous chips, consist of small segments that are separated from each other. These chips typically form when machining brittle materials such as bronze, hard brass, gray cast iron, and materials that are very hard or contain hard inclusions and impurities. Brittle materials lack sufficient ductility for significant plastic deformation during chip formation, leading to repeated fracturing that limits the extent of chip deformation.

Short chips

In less stable machine tools, short cutting chips may cause micro-vibrations during the machining process due to their intermittent formation. One advantage of these chips is that they are easier to handle and clean. When these chips form in brittle materials, such as bronze and gray cast iron, they often result in good surface finish, lower power consumption, and reasonable tool life. However, for ductile materials, discontinuous chips can lead to poorer surface finish and increased tool wear.

5 Methods of Optimizing Cutting Chip Control between Cost and Efficiency 3

Cross-sections of different chip forms

5 Methods of Optimizing Cutting Chip Control between Cost and Efficiency 4

Examples of chip and built-up edge (BUE) formations under different cutting speeds and chip forms in various workpiece materials:

1.Continuous Chips in Carbon Steel

2.Serrated Chips in Duplex Stainless Steel

3.Built-Up Edge (BUE) in Carbon Steel

4.Carbon steel can develop built-up edge (BUE) chip

Discontinuous Chips in Cast Iron

Cast iron typically forms discontinuous cutting chips, consisting of fragmented segments. This occurs due to the brittle nature of cast iron, limiting its ability to form continuous chips during machining.

 

Geometric Shapes of Chip Breakers

Long and continuous cutting chips can adversely affect machining efficiency and pose risks of damaging tools, workpieces, and machine tools. Moreover, issues with cutting chip disposal can lead to unnecessary downtime during production and pose safety hazards to operators. To ensure safety, facilitate chip handling, and prevent damage to machine tools and workpieces, it’s crucial to break these long cutting chips into smaller segments.

Chips bend or curl during formation due to various factors, including:

1.Stress distribution within primary and secondary shear zones.

2.Thermal effects.

3.Strain-hardening characteristics of the workpiece material.

4.Geometric shape of the cutting tool.

The influence of the cooling system also plays a role to some extent.

In essence, reducing the rake angle (using tools with a negative rake angle) tightens the curvature of the cutting chips, making them shorter and more prone to fracture. The function of a chip breaker is to reduce the curvature radius of the cutting chip, thereby promoting the fracture of cutting chips into shorter segments.

 

Basic principles of chip breaker groove geometry

The chip break diagram (refer to the diagram below) illustrates the relationship between workpiece material, cutting conditions, chip breaker type, and cutting chip morphology. This diagram indicates factors to consider when selecting cutting depths and feeds to use specific chip breaker types for machining workpiece materials.

The horizontal axis represents the feed rate, which must always be greater than a certain minimum value (the width of the T-land geometry) and should be less than a maximum value (not exceeding half of the tool nose radius). The vertical axis shows the cutting depth, which should always be greater than the tool nose radius to promote good chip formation and avoid square chip issues. Additionally, the cutting depth should not exceed the cutting edge length. In the latter case, a safety factor is recommended, depending on the strength of the cutting edge. For blades, these safety factors vary between 75% of the cutting edge length (for square or rhombic blades) and 20% (for replica blades with smaller top angles).

 

Showcasing the restrictions imposed by tool groove type, chip shape, and cutting forces on feed rate and cutting depth, all of which together constitute the tool's "chip break" zone.
Showcasing the restrictions imposed by tool groove type, chip shape, and cutting forces on feed rate and cutting depth, all of which together constitute the tool’s “chip break” zone.

 

Cutting depth and feed rate (referred to as chip thickness ratio) must be kept within certain limits. The maximum chip thickness ratio should be maintained below a certain maximum value to avoid excessively long ribbon-like chips. The chip thickness ratio should also be maintained above a minimum value to prevent square chips from forming. These limits are depicted in the diagram with two diagonal lines. The minimum and maximum values of the chip thickness ratio depend on the workpiece material. To minimize cutting edge damage, cutting forces should not be too high. This constraint is represented by a curved line in the diagram.

Within the blue region of the diagram, every combination of feed rate and cutting depth can produce properly shaped chips. Choosing combinations outside the blue region will result in improper chip formation and may lead to excessively long or square chips, or excessive cutting edge damage.

The influence of cutting speed on chip formation
The influence of cutting speed on chip formation

 

The diagram above illustrates the influence of cutting speed on chip formation. The horizontal axis represents the feed rate, and the vertical axis represents the type of chip. Typically, as the feed rate increases, chips tend to become shorter, especially at low cutting speeds. However, as cutting speed increases, the relationship between feed rate and chip formation diminishes.

 

Five Methods for Optimizing Chip Control

1.Determine the priority criterion for process optimization: productivity or cost considerations.

2.If the chip shape is acceptable, go to step 5.

If the chips are too long, go to step 3.

If the chips are too short, go to step 4.

3.If productivity is key, increase the feed rate.

If cost efficiency is key, switch to a stronger chip breaker.

Keep the feed rate within the chip breaker’s range.

Go to step 5.

4.If productivity is key, switch the chip breaker to a sharper one.

If cost considerations are key, reduce the feed rate.

Keep the feed rate within the chip breaker’s range.

Go to step 5.

5.If cost considerations are prioritized, reduce the cutting speed.

If productivity is prioritized, increase the cutting speed.

Добавить комментарий

Ваш адрес email не будет опубликован. Обязательные поля помечены *

国产美女网站在线观看-国产精品亚洲综合网69| 亚洲产国偷v产偷v自拍性色av-亚洲欧美日韩国产三区| 亚洲另类熟女国产精品-懂色一区二区三区在线播放| 黄片黄片在线免费观看-激情综合网激情五月俺也去| 久久精品亚洲国产av久-国产精品视频一区二区免费| 欧洲精品一区二区三区中文字幕-91久久国产综合久久蜜月精品| 91精品国产影片一区二区三区-欧美精品久久久精品一区二区| 少妇人妻无码久久久久久-综合图片亚洲网友自拍| 国语自产偷拍精品视频偷拍-国产伊人这里只有精品视频| 国产精品v欧美精品v日韩精品-国产欧美日韩精品区一区二污污污| 亚洲欧美精品在线一区-99热国产在线手机精品99| 国产精品美女在线网址-久草免费福利在线观看视频| 国产高清av免费在线观看-黄片毛片大全一区二区三区| 婷婷人妻少妇激情在线-欧美日韩人体艺术一区二区| 中文字幕亚洲综合久久最新-久久精品视频免费久久久| 日韩毛片在线免费人视频-超碰中文字幕av在线| 97香蕉久久国产在线观看-麻豆黄色广告免费看片| 亚洲女人黄色录像一区-日韩av电影在线免费看| 午夜精品午夜福利在线-内射无套内射国产精品视频| 免费午夜福利视频在线观看-亚洲成人日韩欧美伊人一区| 亚洲产国偷v产偷v自拍性色av-亚洲欧美日韩国产三区| 人妻日韩精品中文字幕图片-麻豆极度性感诱人在线露脸| 欧美精品国产系列一二三国产真人-在线观看国产午夜视频| 欧美精品啪啪人妻一区二区-嫩草人妻舔舔羞羞一区二区三区| 欧美看片一区二区三区-人妻无卡精品视频在线| 女主播啪啪大秀免费观看-精品99午夜福利影院| 中文字幕日韩精品不卡在线一区-国产tv日韩在线观看视频| 91精品国产影片一区二区三区-欧美精品久久久精品一区二区| 一区二区三区日本韩国欧美-日本1区2区3区4区在线观看| 黑丝av少妇精品久久久久久久-中文字幕久久久人妻无码| 亚洲欧洲一区二区福利-亚洲欧美日韩高清中文| 日韩精品亚洲不卡一区二区-成人网在线视频精品一区二区三区| 久久网址一区二区精品视频-日产国产欧美视频一区精品| 99热在线精品免费6-av一区二区在线观看| 亚洲一区二区少妇激情-国产精品美女久久高潮| 亚洲欧美另类综合偷拍-婷婷社区综合在线观看| 欧美日韩黑人在线播放-51在线精品免费视频观看| 成人免费黄色在线网站-日韩精品一区二区三区四区在线| 久久网站中文字幕精品-三级精品久久中文字幕| 亚洲av成人一区国产精品网-国产偷_久久一级精品a免费| 亚洲福利视频免费观看-中文字幕日本不卡一区二区|