欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

To do a good spin, some basic techniques must be mastered. For a woodspin craftsman, to abandon the decoration of the details or to make the object a little more delicate, the tool must be used perpendicular to the grain of the wood in order to cut the fibers, so that the cut parts are smooth and smooth.

How to Do Lathe in Woodworking? 1

Turning cylindrical works of the end face is different, turning knife is easy to pick out the fiber, resulting in uneven surface.As a result, traditional shaft turning pieces have many arcs decorated with grooves, but very few cylindrical parts.

 Turning tool for shaft turning

The turning tools for shaft turning include semicircle cutting tool, bevel turning tool, shallow groove semicircle knife, cutting tool and so on.The size of the tool depends on the size of the work on the one hand, on the other hand depends on personal habits of operation.

Small turning knives can only be used for small objects, while large turning knives can be used for both large and small objects (although they are not commonly used for small diameter objects or for carving small details).

How to Do Lathe in Woodworking? 2

Turning tools used for shaft turning (from top to bottom) : fine semicircle turning tool, bevel turning tool, spherical turning tool, cutting turning tool, shallow groove and deep groove turning tool

You usually only need a semicircle blank cutter (can be deep groove, also can be shallow groove), can be blank operation.

Bevel turning tool is the most commonly used turning tool for shaft turning.Although the bevel turning knife may give the impression that it is easy to bite, in fact, the biting problem is more serious and destructive.

In contrast, the bite problem of the bevel turning knife is acceptable and does not cause too much damage to the wood.So, you don’t have to worry too much, once you get the hang of it, you’ll be very comfortable with the bevel turning knife.

I like to use a 19 mm wide bevel turning tool for turning objects less than 75 mm in diameter.I like to use a 9 mm thick, 40 mm wide bevel turning tool for larger diameter pieces.

How to Do Lathe in Woodworking? 3

This knife is modified with a scraper, which is heavier, more stable and stronger than the former.In order to ensure that the bevel turning tool slides smoothly along the tool rest, it is necessary to grind the sharp corners on both sides of the turning tool into a slightly convex arc with grinding wheel or grinding rod.

Most of the details need to be handled with a fine 13 mm semicircle knife.For objects less than 30 mm in diameter, a 9 mm fine semicircle knife works better.

General methods of turning

We can spin wood to make it even and smooth without sanding it.The core of the spin is to make the rotating wood come into contact with the blade from the top down.When the blade is at a 45° Angle to the rotating wood, turning is easy and the surface is smooth.Whenever you spin, you should always keep in mind the 45° Angle.As the blade makes more and more contact with the wood, the shavings get smaller and smaller, and when the edge is upright, turning is impossible.

How to Do Lathe in Woodworking? 4

The smaller the Angle between the cutting edge and the wood, the larger the shavings, the higher the probability of bite.When the blade is completely level and at a 90 degree Angle to the wood, it is easy to scratch the wood, leaving an uneven surface.

The core of control rotation is to make the rotating wood contact the tool, rather than forcing the tool into the rotating wood.When the blade of the lathe knife is at the optimal Angle to the wood (about 45°), the wood touches the blade from above and the shavings are cut.

As the shavings are cut off in layers, the blade is pushed slowly towards the wood, taking care not to press the blade against the surface.

How to Do Lathe in Woodworking? 5

Shaft turning is the process of reducing the diameter of wood from large to small, as shown by the arrow in the figure below.

How to Do Lathe in Woodworking? 6

To master the necessary shaft turning techniques, you can practice with square logs with a face length of 50 ~ 65 mm and a length of 250 mm.If the wood is shorter than the tool rest, you can save a lot of time by eliminating the need to adjust the tool rest.Set up the tool rest so that you can hold the tool comfortably.

How to Do Lathe in Woodworking? 7

If the axis of the lathe is close to the height of your elbow, set the tool rest slightly higher than the axis.Gradually lower the height of the tool rest as the diameter of the object becomes smaller.If you are short and the lathe is tall, turn the tool rest down.If you are taller and the lathe is shorter, you should raise the tool rest.

Добавить комментарий

Ваш адрес email не будет опубликован. Обязательные поля помечены *

a一级毛片免费高清在线| 夜夜嗨av少妇一二三区| 久久久久国产AV成人片| 夫妻性生活在线免费视频| 大几吧插进小穴视频| 中国老女人 操逼 视频| 日韩一区二区三区国色天香| 精品精品国产一区二区性色av| 天天舔操操操av| 中文字幕人妻一区二区三区久久| 国产亚洲精品一区久久| 伊人久久综合无码成人网| 欧美精品一区二区三区四区五区| 骚逼毛茸茸乱伦视频| 99久久精品国产一区二区成人了| 国奴精品毛片av一区二区三区| 骚穴手机在线视频| 一级毛片完整版免费播放一区| 久久久五月性色视频| 啊服慢一点插入逼逼| 亚洲综合无码一区二区丶| 久久精品欧美精品免费观看| 啊啊啊别操了视频| 少妇毛片一区二区三区免费视频| 99热这里只有精品97| 亚洲国产成久久成人综合一区| 亚洲 欧美 日韩 主播| 波多野吉衣一区在线观看| 久久高清中文字幕第一页| 国产精品一区二区三区色噜噜| ai换脸久久一区二区亚洲av| 影音先锋天堂网亚洲无码| 青春草在线视频观看| 泰国无码AV片在线观看| 欧美日韩亚洲人人夜夜澡| 女人日比比视频免费| 我想看操小嫩逼大片| 日韩欧美人妻综合| 国产精品白浆一区二区三区| 蜜桃av噜噜一区二区三区免费| 成人黄色精品久久app|