欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

Спиральные сверла и сверла для глубоких отверстий всегда были распространенным выбором в отрасли обработки глубоких отверстий. Мы можем заставить эти два инструмента обрабатывать обычно используемые стали q235, сталь #45 и алюминий, чтобы изучить разницу в качестве поверхности обрабатываемых отверстий, полученных двумя инструментами, а также изменение качества поверхности двух инструментов при разной твердости. материалы.

How twist drills and gun drills work

As shown in the pic 2, the twist drill is generally divided into a straight shank type and a taper shank type. Its working principle is that the drill bit rotates at a high speed under the spindle drive, and the workpiece is continuously fed downward, and the chips are removed from the spiral groove to obtain the desired hole. .

Gun Drill Compares Favorably with Twist Drill 2

During the gun drilling process, the pump outputs high-pressure coolant through the internal hole of the drill pipe into the front cutting area. While cooling and lubricating the tool, the chips are discharged from the high-pressure liquid through the V-groove of the drill pipe to the fuel tank. It can be fixed and then cut by rotating the workpiece, which gives the hole a higher precision.

Gun Drill Compares Favorably with Twist Drill 3


The equipment used for twist drills is generally bench drill and radial drill machine, and can also be done on ordinary milling machines or CNC machines. Most of the gun drills use CNC deep hole machining machines, which require high pressure oil supply and filtration systems.

Processing experiment comparison

1.Cutting speed

The cutting speed can be measured by linear velocity and angular velocity, respectively. The relationship between angular velocity n (r/min) and linear velocity Vc (mm/min) is:

Vc=ndπ/100. d is the effective diameter of the tool

The cutting speeds of different tool materials are different. The following fig.1 is the cutting speed of the gun drill.

Gun Drill Compares Favorably with Twist Drill 4

2. Feed rate Vf

Vf can be expressed in terms of the vertical depth of the tool cut into the workpiece per minute, or by the distance the tool cuts per revolution. For the gun drill feed amount, refer to Table 1. Usually, f=0.01~0.032mm/r is selected. The gun drill feed rate is lower than the twist drill.

3.Coolant oil pressure

The choice of oil pressure P (kg/cm2) is related to the smooth discharge of cooling and chips, and has a great influence on the surface quality of the product. The relationship between cutting pressure and flow rate of gun drill is shown in Table 2.

Gun Drill Compares Favorably with Twist Drill 5

Table 3 shows the experimental conditions of gun drill on #45 steel, Q235 steel and aluminum alloy grade ZL101.

Gun Drill Compares Favorably with Twist Drill 6

Experimental data

After many experiments, the surface roughness values ??of the inlet and outlet of the three materials are shown in Table 4.

Gun Drill Compares Favorably with Twist Drill 7

As can be seen from the above table, the surface roughness of the machined hole of the gun drill is lower than that of the twist drill. Both the gun drill and the twist drill can machine holes with a small roughness on the aluminum. It is worth noting that the chips produced by the twist drill aluminum and Q235 steel are spiral. The gun drill is a straight edge cutter with no spiral flutes, so the chips it produces are mostly sheet-like. In this way, the chips are short, the chip removal is easy, the knife bar is not wound, and the hole wall of the part is not scratched. Moreover, as can be seen from the above table, when processing these three materials, the surface roughness of the gun drilling is close, and the roughness of the hole processed by the twist drill is relatively far. Only when processing in non-ferrous metals, the processing effect of twist drills is closer to that of gun drills, and the physical properties of due to non-ferrous metals are relatively low. In summary, the processing quality of gun drills should be superior to twist drills.

Gun Drill Compares Favorably with Twist Drill 8

So why is this happening? There are 2 reasons below:

1. Twist drills produce relatively large torque during processing. This can cause the axis skew to cause centering difficulties. At this time, the twist of the twist drill can cause burrs. The gun drill has a drill sleeve guide for precise positioning. Therefore, the processed holes have substantially no burrs.

2. Twist drill cutting edge is longer, and the spiral groove will also increase the difficulty of chip removal. The spiral chip friction scratches the hole wall, which is also the cause of the increase in roughness. The gun drill uses hydraulic chip evacuation to lubricate and remove the cutting heat. Protects the surface of the tool and workpiece.

Добавить комментарий

Ваш адрес email не будет опубликован. Обязательные поля помечены *

久操视频中文字幕在线观看| 我要操死你逼视频| 伊人久久亚洲婷婷综合久久| 国产一级a不收费| 国产精品无码毛片久久久| 操大屌粉的小穴视频| 日本一区二区在线高清| 在线看免费无码a片视频| 添女人荫道口视频| 欧美精品视频在线| 美女让我插她的骚逼| 美女扒开腿让男人桶爽揉| 69国产成人综合久久精| 日韩在线中文字幕在线视频| 熟妇丰满大阴户熟妇啪啪| 色熟妇人妻久久中文字幕| 女人被躁到高潮嗷嗷叫小| 亚洲综合欧美日韩| 中文字幕av一区二区三区哈| 人人妻人人澡精品99| 使劲操大骚逼av| 骚逼嫩鸡巴喷水视频| 久久久久久高清无码视频| 内射白嫩少妇超碰| 亚洲精品自拍偷拍第一页| 在线 中文字幕 第一页| 国产精品一区二区在线观看91| 外国处女BB视频| 国产美女裸体视频全免费| 日韩亚洲AV无码一区二区不卡| 久久久久国产AV成人片| 大鸡吧插美女嫩逼| 日韩素人精品亚洲热一区| 一级特一黄大片欧美久久| 蜜臀av一区二区三区免费观| 思思夜免费公开视频| 亚洲欧美一区二区三区孕妇| 最新的亚洲欧美中文字幕| 骚逼少妇被巨根爆插| 抽插肥嫩小穴的视频| 国产女做a爱全免费视频|