Process Measures to Reduce Machining Deformation<\/h1>\n
Reducing Residual Stress in Blanks<\/h2>\n
Natural or artificial aging, as well as vibration treatment, can partially eliminate residual stresses in blanks. Pre-machining is also an effective method. For bulky blanks with excessive stock allowance, post-machining deformation tends to be significant. By pre-machining to remove excess material and balance stock allowance, subsequent machining deformation can be reduced. Additionally, allowing the pre-machined blank to rest helps release residual stresses.<\/p>\n
![\"\"](\"https:\/\/www.meetyoucarbide.com\/wp-content\/uploads\/2025\/04\/u5804245313437012204fm253fmtautoapp138fJPEG.webp\" "\\"\\"")
<\/p>\n
Improving Tool Cutting Performance<\/h2>\n
Tool material and geometric parameters significantly influence cutting forces and heat generation. Proper tool selection is crucial for minimizing part deformation.<\/p>\n
Optimizing Tool Geometry<\/h3>\n
Rake Angle:<\/h4>\n
A larger rake angle (while maintaining edge strength) enhances cutting sharpness, reduces chip deformation, improves chip evacuation, and lowers cutting forces and temperatures. Negative rake angles should be avoided.<\/p>\n
Clearance Angle:<\/h4>\n
The clearance angle directly affects flank wear and surface finish. For rough milling with heavy loads and high heat, a smaller clearance angle improves heat dissipation. For finish milling, a larger clearance angle reduces friction and elastic deformation.<\/p>\n
Helix Angle:<\/h4>\n
A higher helix angle ensures smoother milling and reduces cutting resistance.<\/p>\n
Lead Angle:<\/h4>\n
A smaller lead angle improves heat dissipation and lowers average cutting zone temperatures.<\/p>\n
<\/p>\n
Enhancing Tool Structure<\/h3>\n
Reducing Teeth Count & Increasing Chip Space:<\/h4>\n
Aluminum’s high plasticity demands larger chip pockets. Tools<\/a> with fewer teeth and wider gullets are preferred.<\/p>\n
Precision Edge Honing:<\/h4>\nThe cutting edge roughness should be below Ra = 0.4 \u00b5m. Lightly honing new tools with a fine stone removes burrs and micro-serrations, reducing heat and deformation.<\/p>\n
Strict Wear Control:<\/h4>\n
Tool wear increases surface roughness, cutting temperature, and part deformation. Wear limits should not exceed 0.2 mm to prevent built-up edge. Workpiece temperature should stay below 100\u00b0C to avoid distortion.<\/p>\n
![\"machining](\"https:\/\/www.meetyoucarbide.com\/wp-content\/uploads\/2025\/04\/u1485339483409271644fm253fmtauto.webp\" "\\"\\"")
<\/p>\n
<\/p>\nOptimizing Workpiece Fixturing<\/h2>\n
For thin-walled aluminum parts with low rigidity:<\/p>\n
Axial Clamping for Bushings<\/p>\n
Radial clamping (e.g., 3-jaw chucks) causes post-machining deformation. Instead, use a threaded mandrel inserted into the part\u2019s bore, secured axially with a endplate and nut to maintain precision during OD machining.<\/p>\n
Vacuum Chucks for Thin Plates<\/h3>\n
Uniform clamping force distribution paired with light cuts minimizes distortion.<\/p>\n
Filling Method<\/h3>\n
Fill hollow parts with a low-melting filler (e.g., urea-potassium nitrate melt) to enhance rigidity during machining. Dissolve the filler post-process in water\/alcohol.<\/p>\n
Strategic Process Sequencing<\/h2>\nHigh-speed machining with large stock or interrupted cuts may induce vibration. A typical CNC process flow:<\/p>\n
Roughing \u2192 Semi-finishing<\/a> \u2192 Corner Cleaning \u2192 Finishing<\/p>\n
Operational Techniques to Minimize Machining Deformation<\/h1>\nIn addition to the aforementioned causes, operational methods play a crucial role in controlling deformation during aluminum part machining.<\/p>\n
![\"\"](\"https:\/\/www.meetyoucarbide.com\/wp-content\/uploads\/2025\/04\/u3130168048134940120fm253fmtautoapp138fJPEG.webp\" "\\"\\"")
<\/p>\n
Symmetrical Machining for Large Stock Parts<\/h2>\n
For better heat dissipation, use alternating symmetrical machining. Example: A 90mm plate machined to 60mm achieves 0.3mm flatness when processed in alternating passes versus 5mm with consecutive machining.<\/p>\n
Layered Machining for Multi-cavity Parts<\/h2>\n
Machine all cavities layer-by-layer simultaneously to ensure uniform stress distribution, preventing deformation from uneven forces.<\/p>\n
Optimized Cutting Parameters<\/h2>\n
Adjust depth of cut (ap) with corresponding feed rate and spindle speed increases in CNC high-speed milling to balance productivity and reduced cutting forces.<\/p>\n
Strategic Tool Path Selection<\/h2>\n
Use conventional milling for roughing (maximum removal rate) and climb milling for finishing (better surface quality with progressive chip thickness reduction).<\/p>\n
Thin-wall Fixturing Technique<\/h2>\n
Before final passes, briefly release and reapply minimal clamping force to allow natural recovery, applying force along the part’s most rigid direction.<\/p>\n
Cavity Machining Method<\/p>\n
Avoid direct plunging; pre-drill or use helical entry paths to prevent chip packing and tool breakage.<\/p>\n
![\"\"](\"https:\/\/www.meetyoucarbide.com\/wp-content\/uploads\/2025\/04\/u22800712281232889199fm253fmtautoapp120fJPEG.webp\" "\\"\\"")
<\/p>\n
Conclus\u00e3o<\/h1>\n
Aluminum part deformation stems from material properties, geometry, and processing conditions, primarily involving\u00a0blank residual stresses,cutting forces\/heat,and clamping stresses.The integrated application of these process optimizations and operational techniques significantly reduces deformation, enhances precision and surface quality, providing reliable technical support for production.<\/p><\/div>\n
<\/p>","protected":false},"excerpt":{"rendered":"
There are many causes of deformation in aluminum part machining, which are related to material properties, part geometry, and production conditions. The main factors include: deformation caused by residual stress in the blank, deformation induced by cutting forces and cutting heat, and deformation due to clamping forces. Process Measures to Reduce Machining Deformation Reducing Residual…<\/p>","protected":false},"author":2,"featured_media":23444,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_jetpack_memberships_contains_paid_content":false,"footnotes":""},"categories":[92],"tags":[],"class_list":["post-23440","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-cutting-tools-weekly"],"jetpack_featured_media_url":"https:\/\/www.meetyoucarbide.com\/wp-content\/uploads\/2025\/04\/u22800712281232889199fm253fmtautoapp120fJPEG.webp","jetpack_sharing_enabled":true,"_links":{"self":[{"href":"https:\/\/www.meetyoucarbide.com\/pt\/wp-json\/wp\/v2\/posts\/23440","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.meetyoucarbide.com\/pt\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.meetyoucarbide.com\/pt\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.meetyoucarbide.com\/pt\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/www.meetyoucarbide.com\/pt\/wp-json\/wp\/v2\/comments?post=23440"}],"version-history":[{"count":2,"href":"https:\/\/www.meetyoucarbide.com\/pt\/wp-json\/wp\/v2\/posts\/23440\/revisions"}],"predecessor-version":[{"id":23446,"href":"https:\/\/www.meetyoucarbide.com\/pt\/wp-json\/wp\/v2\/posts\/23440\/revisions\/23446"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.meetyoucarbide.com\/pt\/wp-json\/wp\/v2\/media\/23444"}],"wp:attachment":[{"href":"https:\/\/www.meetyoucarbide.com\/pt\/wp-json\/wp\/v2\/media?parent=23440"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.meetyoucarbide.com\/pt\/wp-json\/wp\/v2\/categories?post=23440"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.meetyoucarbide.com\/pt\/wp-json\/wp\/v2\/tags?post=23440"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}
<\/p>\n<\/p>\n