欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

There are many causes of deformation in aluminum part machining, which are related to material properties, part geometry, and production conditions. The main factors include: deformation caused by residual stress in the blank, deformation induced by cutting forces and cutting heat, and deformation due to clamping forces.

Process Measures to Reduce Machining Deformation

Reducing Residual Stress in Blanks

Natural or artificial aging, as well as vibration treatment, can partially eliminate residual stresses in blanks. Pre-machining is also an effective method. For bulky blanks with excessive stock allowance, post-machining deformation tends to be significant. By pre-machining to remove excess material and balance stock allowance, subsequent machining deformation can be reduced. Additionally, allowing the pre-machined blank to rest helps release residual stresses.

Causes Analysis and Process Control Measures for Machining Deformation of Aluminum Components 2

Improving Tool Cutting Performance

Tool material and geometric parameters significantly influence cutting forces and heat generation. Proper tool selection is crucial for minimizing part deformation.

Optimizing Tool Geometry

Rake Angle:

A larger rake angle (while maintaining edge strength) enhances cutting sharpness, reduces chip deformation, improves chip evacuation, and lowers cutting forces and temperatures. Negative rake angles should be avoided.

Clearance Angle:

The clearance angle directly affects flank wear and surface finish. For rough milling with heavy loads and high heat, a smaller clearance angle improves heat dissipation. For finish milling, a larger clearance angle reduces friction and elastic deformation.

Helix Angle:

A higher helix angle ensures smoother milling and reduces cutting resistance.

Lead Angle:

A smaller lead angle improves heat dissipation and lowers average cutting zone temperatures.

 

Enhancing Tool Structure

Reducing Teeth Count & Increasing Chip Space:

Aluminum’s high plasticity demands larger chip pockets. Tools with fewer teeth and wider gullets are preferred.

Precision Edge Honing:

The cutting edge roughness should be below Ra = 0.4 μm. Lightly honing new tools with a fine stone removes burrs and micro-serrations, reducing heat and deformation.

Strict Wear Control:

Tool wear increases surface roughness, cutting temperature, and part deformation. Wear limits should not exceed 0.2 mm to prevent built-up edge. Workpiece temperature should stay below 100°C to avoid distortion.

machining deformation

Optimizing Workpiece Fixturing

For thin-walled aluminum parts with low rigidity:

Axial Clamping for Bushings

Radial clamping (e.g., 3-jaw chucks) causes post-machining deformation. Instead, use a threaded mandrel inserted into the part’s bore, secured axially with a endplate and nut to maintain precision during OD machining.

Vacuum Chucks for Thin Plates

Uniform clamping force distribution paired with light cuts minimizes distortion.

Filling Method

Fill hollow parts with a low-melting filler (e.g., urea-potassium nitrate melt) to enhance rigidity during machining. Dissolve the filler post-process in water/alcohol.

Strategic Process Sequencing

High-speed machining with large stock or interrupted cuts may induce vibration. A typical CNC process flow:

Roughing → Semi-finishing → Corner Cleaning → Finishing

For high-precision parts, repeat semi-finishing before final passes. Post-roughing natural cooling relieves stresses. Leave 1–2 mm stock after roughing; maintain 0.2–0.5 mm uniform allowance in finishing to ensure stability, reduce deformation, and achieve high surface quality.

Operational Techniques to Minimize Machining Deformation

In addition to the aforementioned causes, operational methods play a crucial role in controlling deformation during aluminum part machining.

Causes Analysis and Process Control Measures for Machining Deformation of Aluminum Components 3

Symmetrical Machining for Large Stock Parts

For better heat dissipation, use alternating symmetrical machining. Example: A 90mm plate machined to 60mm achieves 0.3mm flatness when processed in alternating passes versus 5mm with consecutive machining.

Layered Machining for Multi-cavity Parts

Machine all cavities layer-by-layer simultaneously to ensure uniform stress distribution, preventing deformation from uneven forces.

Optimized Cutting Parameters

Adjust depth of cut (ap) with corresponding feed rate and spindle speed increases in CNC high-speed milling to balance productivity and reduced cutting forces.

Strategic Tool Path Selection

Use conventional milling for roughing (maximum removal rate) and climb milling for finishing (better surface quality with progressive chip thickness reduction).

Thin-wall Fixturing Technique

Before final passes, briefly release and reapply minimal clamping force to allow natural recovery, applying force along the part’s most rigid direction.

Cavity Machining Method

Avoid direct plunging; pre-drill or use helical entry paths to prevent chip packing and tool breakage.

Causes Analysis and Process Control Measures for Machining Deformation of Aluminum Components 4

Conclus?o

Aluminum part deformation stems from material properties, geometry, and processing conditions, primarily involving?blank residual stresses,cutting forces/heat,and clamping stresses.The integrated application of these process optimizations and operational techniques significantly reduces deformation, enhances precision and surface quality, providing reliable technical support for production.

Deixe uma resposta

O seu endere?o de e-mail n?o será publicado. Campos obrigatórios s?o marcados com *

久久久久人妻一区精品加勒比| 那种视频在线观看你懂的| 久久综合娱乐中文网| 少妇无码一区二区二三区| 美女骚逼被操出白浆| 操烂嫩逼内射视频| 一区二区三区国产l精品欧美| 免费女人男人肏逼| 欧美丰满大屁股女人的逼被操视频| 精品一二三四区中文字幕| 国产乱理伦片在线观看夜| 中文字幕亚洲欧美精品一区二区| 毛片日产av一区二区三区四区| 欧美日韩视频在线一区二区| 最新免费高清无码片| 女同舔我下面直流水| 瓯美在线免费视频笫一区第二区| 大鸡巴操逼视频免费| 国产熟女视频一区二区三区| 白色紧身裤无码系列在线| 日韩精品一区二区天堂| 奇米一区二区三区视频在线观看| 性一交一乱一乱一区二区| 黑人大屌爆操骚货| 国产精品久久久久妇| 最新的亚洲欧美中文字幕| 亚洲国产综合精品 在线 一区| 日本人色频在线看观| 成人毛片一级特黄| 狠狠五月激情综合去干网| 国产精品自在自线。| 亚洲精品国产综合一线久久| 美国业余自由摘花管| 国产精品白浆一区二区三区| 激情五月六月婷婷俺来也| 中文字幕一区二区日韩精品蜜臂| 中文字幕乱码一区三区免费| 从后面进入嗯啊视频| 非洲男生操男生屁眼视频| 少妇毛片一区二区三区免费视频| 国产精品人妇一区二区三区|