欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

Zjawiska fizyczne w obróbce tytanu

The cutting force of titanium alloy is only slightly higher than that of steel with the same hardness, but the physical phenomenon of titanium alloy processing is much more complex than that of steel processing, which makes the titanium alloy processing face great difficulties.

Dlaczego tytan jest materia?em trudnym do obrabiania? 2)

Most titanium alloys have very low thermal conductivity, only 1 / 7 of steel and 1 / 16 of aluminum. Therefore, the heat generated in the process of cutting titanium alloy will not be transferred to the workpiece or taken away by the chips, but gathered in the cutting area, the generated temperature can be as high as 1000 ℃ or above, which makes the cutting edge of the tool wear, crack and generate chip tumor rapidly, and the worn cutting edge appears rapidly, which makes the cutting area generate more heat, further shortening the service life of the tool.

The high temperature produced in the cutting process destroys the surface integrity of titanium alloy parts at the same time, which leads to the decrease of geometric accuracy of parts and the phenomenon of work hardening that seriously reduces their fatigue strength.

The elasticity of titanium alloy may be beneficial to the performance of parts, but in the process of cutting, the elastic deformation of workpiece is an important reason for vibration. The cutting pressure makes the “elastic” workpiece leave the tool and rebound, so that the friction between the tool and the workpiece is greater than the cutting effect. The friction process also produces heat, which aggravates the problem of poor thermal conductivity of titanium alloy.

When machining thin-walled or ring shaped parts, this problem is more serious. It is not easy to process titanium alloy thin-walled parts to the expected dimensional accuracy. Because when the workpiece material is pushed away by the cutter, the local deformation of the thin wall has exceeded the elastic range, resulting in plastic deformation, and the material strength and hardness of the cutting point increase significantly. At this time, according to the originally determined cutting speed, the machining becomes too high, which further leads to sharp tool wear.

Dlaczego tytan jest materia?em trudnym do obrabiania? 3)

“Heat” is the “culprit” of titanium alloy difficult to process!

Technological know-how of titanium alloy processing

On the basis of understanding the processing mechanism of titanium alloy and previous experience, the main know-how of processing titanium alloy is as follows:

(1) The blade with positive angle geometry is used to reduce cutting force, cutting heat and workpiece deformation.

(2) Keep constant feeding to avoid hardening of workpiece. During the cutting process, the tool should always be in the feeding state. The radial cutting amount AE should be 30% of the radius.

(3) High pressure and large flow cutting fluid are used to ensure the thermal stability of the machining process and prevent the surface degeneration and tool damage due to the high temperature.

(4) Keeping the blade edge sharp and blunt is the cause of heat accumulation and wear, which is easy to lead to tool failure.

(5) It can be processed in the softest state of titanium alloy as much as possible, because the material becomes more difficult to process after hardening, heat treatment improves the strength of the material and increases the wear of the blade.

(6) Use large tip radius or chamfer to cut in, and try to put more blades into cutting.  This can reduce the cutting force and heat at each point and prevent local damage. In the milling of titanium alloy, the cutting speed has the greatest influence on the tool life VC, followed by the radial cut (milling depth) AE.

Dlaczego tytan jest materia?em trudnym do obrabiania? 4

Starting from blade to solve the problem of titanium processing

The groove wear of the blade in titanium alloy machining is the local wear of the back and front along the cutting depth direction, which is often caused by the hardening layer left by the previous machining. The chemical reaction and diffusion of cutting tool and workpiece material at the processing temperature over 800 ℃ is also one of the reasons for the formation of groove wear. Because in the process of machining, titanium molecules of the workpiece accumulate in front of the blade, and “weld” to the blade under high pressure and high temperature, forming chip accretion tumor. When the chip accretion is peeled from the blade, the cemented carbide coating of the blade is taken away. Therefore, special blade material and geometry are required for titanium alloy processing.

Tool structure suitable for titanium machining

The focus of titanium alloy machining is heat. A large amount of high-pressure cutting fluid should be sprayed on the cutting edge timely and accurately to remove the heat quickly. There is a unique structure of milling cutter specially used for titanium alloy processing on the market.

亚洲精品成a人在线观看| 美女穿黑丝被大鸡巴猛操| 国产成人AV剧情| 久久精品国产亚洲av伦理| 久久99热人妻偷产精品| 操我骚逼抽插视频| 操我好舒服用力视频| 日日爱黄色毛片视频| 男人大鸡巴操小鲜肉视频| 九九视频精品只有这里有| 老司机精品成人无码AV| 国产高清第一区第二区第一页| 啦啦啦视频在线手机播放| 黑人妖大鸡吧操逼| 午夜福利在线观看aaa| 美女大骚逼幸福遍穴| 精品无码国产一区二区三区麻豆| 在线 中文字幕 第一页| 欧美国产三级片久久高清| 神马我不卡手机在线观看| 三级片成人京东热五月天| 啊啊啊啊大鸡巴操我视频| 精品麻豆国产免费一区二区三区| 粗大长内射女人视频| 中国三级片在线视频| 国产精品操大屁股老淑女| 视频在线观看一区@99| 精品久久久久亚洲中文字幕| 国产亚洲欧美日韩在线观看一区| 欧美后入尻逼视频| 国产成人亚洲精品在线看| 国产尤物蜜臀AV| 国产精品熟女一区二区三区久久夜| 男生操女生无马赛克免费| 97超级免费视频在线观看| 久久久国产了楼凤| 久久精品一区二区三区免费看| 男生插女生下面流出白色精液视频| 阴茎大头插少妇蜜穴视频| 男女插插调教骚逼| 99热这里只有精品98|