欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

Aby wykona? dobry obrót, nale?y opanowa? kilka podstawowych technik. Dla rzemie?lnika, aby zrezygnowa? z ozdabiania detali lub uczyni? przedmiot nieco delikatniejszym, narz?dzie musi by? u?ywane prostopadle do s?ojów drewna w celu przeci?cia w?ókien, tak aby ci?te cz??ci by?y g?adkie i g?adkie .

How to Do Lathe in Woodworking? 1

Turning cylindrical works of the end face is different, turning knife is easy to pick out the fiber, resulting in uneven surface.As a result, traditional shaft turning pieces have many arcs decorated with grooves, but very few cylindrical parts.

 Turning tool for shaft turning

The turning tools for shaft turning include semicircle cutting tool, bevel turning tool, shallow groove semicircle knife, cutting tool and so on.The size of the tool depends on the size of the work on the one hand, on the other hand depends on personal habits of operation.

Small turning knives can only be used for small objects, while large turning knives can be used for both large and small objects (although they are not commonly used for small diameter objects or for carving small details).

How to Do Lathe in Woodworking? 2

Turning tools used for shaft turning (from top to bottom) : fine semicircle turning tool, bevel turning tool, spherical turning tool, cutting turning tool, shallow groove and deep groove turning tool

You usually only need a semicircle blank cutter (can be deep groove, also can be shallow groove), can be blank operation.

Bevel turning tool is the most commonly used turning tool for shaft turning.Although the bevel turning knife may give the impression that it is easy to bite, in fact, the biting problem is more serious and destructive.

In contrast, the bite problem of the bevel turning knife is acceptable and does not cause too much damage to the wood.So, you don’t have to worry too much, once you get the hang of it, you’ll be very comfortable with the bevel turning knife.

I like to use a 19 mm wide bevel turning tool for turning objects less than 75 mm in diameter.I like to use a 9 mm thick, 40 mm wide bevel turning tool for larger diameter pieces.

How to Do Lathe in Woodworking? 3

This knife is modified with a scraper, which is heavier, more stable and stronger than the former.In order to ensure that the bevel turning tool slides smoothly along the tool rest, it is necessary to grind the sharp corners on both sides of the turning tool into a slightly convex arc with grinding wheel or grinding rod.

Most of the details need to be handled with a fine 13 mm semicircle knife.For objects less than 30 mm in diameter, a 9 mm fine semicircle knife works better.

General methods of turning

We can spin wood to make it even and smooth without sanding it.The core of the spin is to make the rotating wood come into contact with the blade from the top down.When the blade is at a 45° Angle to the rotating wood, turning is easy and the surface is smooth.Whenever you spin, you should always keep in mind the 45° Angle.As the blade makes more and more contact with the wood, the shavings get smaller and smaller, and when the edge is upright, turning is impossible.

How to Do Lathe in Woodworking? 4

The smaller the Angle between the cutting edge and the wood, the larger the shavings, the higher the probability of bite.When the blade is completely level and at a 90 degree Angle to the wood, it is easy to scratch the wood, leaving an uneven surface.

The core of control rotation is to make the rotating wood contact the tool, rather than forcing the tool into the rotating wood.When the blade of the lathe knife is at the optimal Angle to the wood (about 45°), the wood touches the blade from above and the shavings are cut.

As the shavings are cut off in layers, the blade is pushed slowly towards the wood, taking care not to press the blade against the surface.

How to Do Lathe in Woodworking? 5

Shaft turning is the process of reducing the diameter of wood from large to small, as shown by the arrow in the figure below.

How to Do Lathe in Woodworking? 6

To master the necessary shaft turning techniques, you can practice with square logs with a face length of 50 ~ 65 mm and a length of 250 mm.If the wood is shorter than the tool rest, you can save a lot of time by eliminating the need to adjust the tool rest.Set up the tool rest so that you can hold the tool comfortably.

How to Do Lathe in Woodworking? 7

If the axis of the lathe is close to the height of your elbow, set the tool rest slightly higher than the axis.Gradually lower the height of the tool rest as the diameter of the object becomes smaller.If you are short and the lathe is tall, turn the tool rest down.If you are taller and the lathe is shorter, you should raise the tool rest.

Dodaj komentarz

Twój adres email nie zostanie opublikowany. Pola, których wype?nienie jest wymagane, s? oznaczone symbolem *

avtt天堂网先锋伦理| 大几吧插进小穴视频| 女人被躁到高潮嗷嗷叫小| 插女人下面高潮视频| 99视频在线看免费视频| 韩国女主播一区二区视频| 一区二区三区 日韩在线| 九九在线精品亚洲国产| 中日韩国内精品视频| 从后面狠狠的干白嫩少妇| 二次元男生操女生屁眼爽| 狗狗大鸡巴狂操美女| 从后面狠狠的干白嫩少妇| 在线免费观看一区| 国产精选三级在线观看| 大鸡巴抽插小骚逼视频免费| 啊灬啊别停灬用力啊男男在线观看| 亚洲国产无线码在线| 久久精精品久久久久噜噜| 色噜噜AV亚洲色一区二区| 另类 专区 综合 中文| 国产一级a不收费| 精品久久久久五月婷五月| 中文字幕国产精品一区二区三区| 精品国产自在现线看| 一级特黄大片色欧美精品| 国产精品碰碰现在自| 成年人的一级黄色带| 男生鸡鸡插进女生笑穴里| 最新日本一区二区三区免费看| 人人妻人人澡精品99| 男人把鸡巴插入女人| 国产高清一区二区三区四区色| 视频一区视频二区制服丝袜| 国产情侣色综合久久有码| 欧美精品国产一区二区在线观看| 久久免费国产视频| 中文字幕国产精品一区二区三区| 99亚洲精品高清一二区| 操逼动漫首页登录| 国产精品亚洲一区二区三区极品|