欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

Surface roughness is an indicator used to measure the degree of surface micro-irregularities, and it is commonly annotated on mechanical drawings with roughness symbols. The types of roughness symbols include surface roughness symbols, roughness codes, and additional descriptions. The following is a detailed introduction to the types of roughness annotations.

Figure 1. Schematic of roughness surface profile hatching.

Surface Roughness Symbol

4 Points of Machining Surface Roughness You Need to Know 1

4 Points of Machining Surface Roughness You Need to Know 2

a?、a?— symbols and values for the roughness height

parameters (unit is μm);

b — machining requirements, plating, coating, surface treatment, or other descriptions;

c — sampling length (in millimeters) or waviness (in micrometers);

d — symbol for the direction of the machining texture;

e — machining allowance (in millimeters);

f — roughness spacing parameter (in millimeters) or profile support length ratio.

?Other Annotation Descriptions

  • Sampling Length: The length range selected when measuring roughness, used to calculate roughness parameters.
  • Evaluation Length: The total sum of the sampling lengths, used to assess surface roughness.
  • Machining Method: Indicates the machining method by which the surface roughness is achieved, such as turning, grinding, etc.
  • Other Requirements: For example, surface treatment (such as sandblasting, polishing, etc.), texture direction, etc.
Machining Texture Requirements
Machining Texture Requirements

4 Points of Machining Surface Roughness You Need to Know 34 Points of Machining Surface Roughness You Need to Know 4

Roughness Code

Arithmetic Mean Roughness Ra

Arithmetic mean roughness is the most commonly used roughness parameter, representing the arithmetic average of the absolute values of the profile peaks and valleys within the sampling length. When selecting the reference length in the direction of the mean line from the roughness curve, using the direction of the mean line of the selected part as the X-axis and the direction of the vertical magnification as the Y-axis, if the roughness curve is represented as y=f(x), the value obtained from the following formula, when expressed in micrometers (μm), is called the arithmetic mean roughness Ra.

4 Points of Machining Surface Roughness You Need to Know 5

Arithmetic Mean Roughness ?

Note: The arithmetic mean roughness Ra is the most commonly used expression for roughness. Unless otherwise specifically noted, roughness generally refers to Ra.

From the roughness curve, a reference length is selected in the direction of the mean line. From the values measured in the direction of the vertical magnification from the mean line of the selected part, the sum of the average absolute values of the peak elevations (Yp) from the highest peak to the fifth peak and the average absolute values of the valley elevations (Yv) from the lowest valley to the fifth valley is calculated. This sum is referred to as the value expressed in micrometers (μm).

Ten-Point Average Roughness Rz
Ten-Point Average Roughness Rz

Maximum Height Ry

The maximum profile height, which represents the vertical distance between the highest profile peak and the deepest valley within the sampling length. From the roughness curve, a reference length is selected in the direction of the mean line. The interval between the peak line and the valley line of the selected part is measured in the direction of the vertical magnification of the roughness curve, and this value is called the micrometer value (μm).

Note: When determining Ry, the reference length should be selected from a section of the curve that is free of cracks and extreme peaks and valleys.

Maximum Height Ry
Maximum Height Ry

Labeling Example

Label the upper limit value of Ra

4 Points of Machining Surface Roughness You Need to Know 6

  • Control the surface roughness to within 25μm by any means.
  • Control the surface roughness to within 6.3μm by material removal methods.
  • Control the surface roughness to within 25μm without removing material.

Label the direction of the machining texture

4 Points of Machining Surface Roughness You Need to Know 7

Note: The direction of the machined tool texture is perpendicular to the projection plane marked with symbols.

Label the upper and lower limits of Ra

4 Points of Machining Surface Roughness You Need to Know 8

Control the surface roughness to a minimum of 1.6μm and a maximum of 6.3μm by removing material. Generally, the upper and lower limit values are marked for oil seal installation holes, as roughness that is too large or too small can affect the sealing effect of the oil seal.

Label the machining methodsurface roughness

Marking Machining Method

Attention Points Marking Position: The roughness symbol is usually annotated above or below the dimension line, close to the surface being marked.

Direction Guide Line: The direction guide line should point towards the surface being marked and be parallel or perpendicular to the surface.

Value Unit: The roughness values are typically expressed in micrometers (μm).

?? ???

???? ???? ????. ?? ???? * ? ???? ????

日韩无码av三级片| 少妇毛片一区二区三区免费视频| 亚洲精品国产综合一线久久| 好想插进去捅一捅| 国产精品自在拍首页| 美性中文网中文字幕91| 啦啦啦视频在线手机播放| 中文字幕亚洲精品女同一页| 激烈18禁高潮视频免费| 日本 视频 一区二区| 日逼动态视频免费看| 骚逼嫩鸡巴喷水视频| 内射白嫩少妇超碰| 日本高清一区二区三区水蜜桃| 日本一区二区高清免费不卡| 人人超级碰青青精品| 亚洲国产成久久成人综合一区| 国产高清第一区第二区第一页| 亚洲综合网伊人中文| 中文字幕无码区一区二区| 国产在线中文字幕一区二区三区| 日本 日韩 欧美| 韩国女主播一区二区视频| 无码爆一二三区免费视频| 骚片视频在线观看| 欲色欲香天天网综合久久| 国产精选三级在线观看| 国产成人无码AV一区二区三区| 色欲精品一区二区三区AV| 久久精品伦一区二区三区| 欧美国产三级片久久高清| 亚洲AV无码一区二区三区系列| 国产一区二区三区午夜精品久久| 白嫩在线亚洲观看| 9国产亚洲精品国产| 操纯欲女生小穴视频| 欧美大胆a级视频 一本| 泰国无码AV片在线观看| 男女操逼视频嫩嫩| 熟妇丰满大阴户熟妇啪啪| 国产成人AV一区二区在线观看|