欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

In the bearing and standard parts industry, steel balls and screws are produced using highly efficient automatic cold heading machines. These machines have high production rates, but for medium and large-sized steel balls, the life and efficiency of the matching alloy steel dies are reduced due to the following factors during the cold heading process:

Wear and deformation caused by the intense flow of the deformed metal on the die surface. Sometimes, the die cavity surface is scratched, abraded, or even adhered to, which easily causes dimensional errors and scrapping of the die, resulting in poor product quality.

The die cavity is easily deformed due to the relatively insufficient yield strength of the matrix material.

After continuous and repeated stress, especially in areas with stress concentration, the fatigue life of the alloy steel is relatively low, leading to fatigue failure as the number of heading operations increases.

Therefore, in addition to further improving the life of alloy steel dies, there is a widespread demand for a new material that is both wear-resistant and has good toughness to adapt to the development of the cold heading industry.

Test Results and Application Assessment

To expand the application field of cemented carbide and meet the urgent demand of steel ball factories for large-sized steel ball cemented carbide dies, based on our long-term work experience and domestic and foreign data collection, we finally selected a specially made coarse-grained WC powder, supplemented by an appropriate binder phase, to formulate YGC-I and YGC-Ⅱ coarse-grained cemented carbides (YGC-Ⅱ has a higher binder phase content than YGC-I). The conventional performance data of YGC-I and YGC-Ⅱ are shown in Table 1.

An Application of Coarse-Grained Cemented Carbide in Cold Heading Dies for Steel Balls 2

To study the effect of different particle sizes of WC powder on the fracture toughness of cemented carbide, fine-grained cemented carbide YG10X, medium-coarse grained cemented carbide YG18C, and YG20C were also prepared.

The fracture toughness of fine-grained, medium-coarse grained, and super-coarse grained cemented carbides with three different WC particle sizes was measured, and the results are shown in Table 2. It can be observed from Table 2 that as the WC particle size changes from fine-grained to medium-coarse grained and then to coarse grained, the fracture toughness of the alloy increases significantly, or even doubles. Even within the same particle size range, the fracture toughness of the alloy also increases with the increase of the binder phase content. This indicates that there are two ways to improve the fracture toughness of the alloy: first, by selecting coarse-grained WC powder, and second, by increasing the binder phase content of the alloy.

An Application of Coarse-Grained Cemented Carbide in Cold Heading Dies for Steel Balls 3

carbide material for cold heading

Selected YGC-I and YG10X samples were used to take scanning electron microscopy (SEM) fracture photos. Figure 1a shows the SEM fracture photo of YGC-I, and Figure 1b shows the SEM fracture photo of YG10X. Careful observation of the SEM fracture photos reveals that YGC-I has coarse grains and a thick binder phase layer, with cracks extending along the binder phase, resulting in mostly intergranular fractures and thus a higher fracture toughness K?C. In contrast, YG10X has very fine grains and a very thin binder phase layer, with mostly transgranular fractures, leading to a lower fracture toughness K?C. This indicates that the trend in fracture toughness values of carbides with different grain sizes is consistent with the conclusions drawn from the analysis of SEM fracture photos.

The aforementioned coarse-grained cemented carbide developed was applied to cold heading larger specification steel balls φ17.4625 and φ19.05. After being used on a Z32-28 machine at a certain factory, the usage data show that the coarse-grained cemented carbide is capable of stamping larger specification steel balls, and its die core life is more than 8 to 10 times longer than that of GCr15. This not only expands the application scope of cemented carbide but also provides the possibility for the bearing industry and standard parts industry to adopt carbide dies with larger heading forces. Moreover, due to the significant increase in die life, it brings about considerable economic benefits.

??

1.Selecting specially made coarse-grained WC powder and correspondingly increasing the binder phase content of the alloy is an effective way to improve the fracture toughness of cemented carbide.

2.SEM fracture analysis indicates that coarse-grained cemented carbide fractures are mostly intergranular, resulting in a higher fracture toughness K?C, while fine-grained cemented carbide fractures are mostly transgranular, leading to a lower fracture toughness K?C.

3.The usage results show that the life of coarse-grained cemented carbide die cores is more than 8 to 10 times longer than that of GCr15.

4.In summary, for the stamping of larger specification steel balls, choosing coarse-grained cemented carbide is a reasonable option.

?? ???

???? ???? ????. ?? ???? * ? ???? ????

日本最新免费不卡一区二区三区| 亚洲国产成人久久成人52| 亚洲欧美日韩另类| 午夜福利国产三级片| 国产 欧美 日韩 黄片| 亚洲国产成人久久成人52| 国产精品碰碰现在自| 日本潘金莲三级bd高清| 男人草女人的骚逼逼| 精彩欧美一区二区三区| 无遮挡粉嫩久久久久久久| 老司机午夜精品视频无码| 性色av一区二区三区天美传媒四| 日本人妻与家公的伦理片| 91成人精品国语自产拍| 日韩欧美一区二三区风间由美| 这里只有久久精品| 久久99热精品在线观看| 偷窥国内肥臀老熟女视频| 久久国产老熟女老女人| 亚洲午夜国产片在线观看| 中文国产成人精品久久久| 在线 中文字幕 第一页| 中文欧美亚洲欧日韩| 国产尤物蜜臀AV| 另类 专区 综合 中文| 亚洲av午夜福利精品一区| 欧美日本欧美日本区一区二| 日韩精品无码一区二区三区不卡| 啊啊啊啊大鸡巴操我视频| 欧美 日韩 国产 自拍| 99爱这里只有精品| 小美女淫荡的视频| 久久亚洲精品中文字幕一| 亚洲大尺度无码无码专线一区| 可以免费看污污片的软件| 90岁肥老奶奶毛毛外套| 欧美成人精品一区二区免费看| 操鸡巴奶子在线观看| 在线无码一区二区三区不卡| 久久久久久国产A免费观看|