欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

The bearing capacity, rotation accuracy and antifriction performance of rolling bearing will change due to its own quality and external conditions in the use process. When the performance index of bearing is lower than the use requirements and cannot work normally, it is called bearing damage or failure. Once the bearing is damaged and other unexpected conditions occur, the machine and equipment will stop running and the function will be damaged And other abnormal phenomena.

If the bearing is broken, the cause of the damage should be analyzed first, and then a solution should be found. Therefore, it is necessary to find out the causes in a short time and take corresponding measures.

Bearing is a loss type part, as long as it is used, it will definitely be damaged. Only to accumulate to a certain extent can it be displayed, that is to say, to a certain amount can it be bad. Of course, the damage of rolling bearing is much more complicated than that of general mechanical parts. The characteristics of the damage of rolling bearing are many forms and complicated reasons. Apart from the internal factors of bearing design and manufacturing, most of the damage of bearing is due to improper use, such as: suitable selection of type cloth (refer to the instructions of customers), support Unreasonable design, improper installation, poor lubrication, poor sealing and other external factors. The following 8 points are the main factors of bearing failure:

1. Metal corrosion

If lack of lubrication, it is easy to be oxidized and rusted by air. To prevent bearing corrosion, do not use blisters. Bearings are made of fine steel, but they are also afraid of water. When the bearing is taken by hand, the sweat on the hand shall be fully washed off, and the operation shall be carried out after the application of high-quality mineral oil. In rainy season and summer, special attention shall be paid to rust prevention.

The specific causes of bearing natural corrosion and wear are as follows:

① Oxidation wear. The tiny peaks and valleys on the friction surface are squeezed each other, making the brittle surface gradually fall off and wear. The tiny peaks and troughs on the surface of the relative movement of the bearing and the oxidation synthesis in the air generate brittle oxide which is not firmly bonded with the base metal. The oxide is easy to fall off in the friction, and the wear is called oxidation wear.

② Friction causes hot wear. When the bearing works under the condition of high speed and heavy load and poor lubrication, the high temperature, the hardness of the contact point and the wear resistance decrease, even adhesion and tear occur at the peak and valley of the surface due to friction. This kind of wear is called friction heat wear.

③ Hard grain wear. If the bearing is in relative motion. The structure of the moving surface of the bearing is uneven, and there are hard particles, or there are impurities such as sand, friction chips and chips falling between the moving surfaces of the bearing. In the relative movement of the bearing, the hard particles or impurities will scratch the surface of the bearing and even form grooves, which is called hard particle wear. Automobile bearing

④ Pitting wear. Gear, bearing and other rolling contact surfaces are periodically subjected to great contact pressure in the relative process. Under the long-term action, the fatigue phenomenon occurs on the metal surface, which causes micro cracks and denudation on the bearing surface. This kind of wear is called pitting wear.

To cause rust or corrosion, abrasion by chemical action. The bearing surface is corroded by acid, alkali, salt liquid or harmful gas. It accelerates the wear process, which is called the wear caused by chemical corrosion.

Corrosion damage due to temporary contact with water, acid, alkali, salt and other liquids or harmful gases: non moving bearing on equipment. Damage caused by rust or corrosion is called corrosion damage.

2. The bearing is overloaded or improperly used

The load of bearing shall not be exceeded when using. Like a car, it may be that if the load is too heavy, it is easy to damage the bearings. So there are more truck problems than cars, which are caused by many parts that can’t withstand.

Why are Your Bearing Parts Broken so Easily? Let’s Listen to What Professional Engineers Say about It 1

3. The bearing clearance is too small

The front wheel of the car is an inclined push bearing, which needs to adjust the clearance. Too loose will lead to abnormal noise, deflection and wheel shaking. Too tight will accelerate wear, both are bad. For the old bearing, it is necessary to check whether there are burrs, scratches and cracks on the ball (column) surface. Whether the radial clearance and axial clearance of the old bearing are qualified is generally only measured. For new bearings, first check whether the bearing model is correct. Refer to table 1 for the standard of radial clearance of rolling bearing. For example, model 6318 deep groove ball bearing has an inner diameter of 90mm and a radial clearance range of 0.016-0.046mm. It can also be found that the maximum wear of the bearing is 0.25mm.

4. Use inferior bearing

Bearing production is produced by some small factories. The production process can not meet the requirements. The accuracy of the shaft or bearing box is poor. Bearing steel is not processed, so it is pressed and produced. Therefore, the bearing produced is not durable.Why are Your Bearing Parts Broken so Easily? Let’s Listen to What Professional Engineers Say about It 2

5. Reckless driving may also cause car bearing damage

But that’s a bit far fetched. Because of careless driving, other parts will be damaged before the bearing.

6. Poor installation

To install the bearing, follow the installation steps of the bearing, and do not install or disassemble it roughly. Whether the bearing is installed correctly or not is related to the service life of the bearing, so we must pay attention to it. When installing the bearing, do not use the hand directly, because the sweat on the hand may also cause corrosion, do not ignore the small links. During the bearing installation, the most important thing is not to allow strong stamping, not to directly hit the bearing with a hammer, not to be afraid of being damaged, but to be afraid of being damaged or deformed, and the deformed bearing will not be used. Also, it is not allowed to transfer pressure through the rolling element.

7. Foreign matter intrusion

Try to use special tools, try to avoid using cloth and short fiber and other things, so as to avoid unnecessary damage caused by fine fiber into the bearing. For example, when installing the bearing, the staff used to knock in the copper bar, which was easy to cause the bearing axial force uneven, resulting in the cage deformation, the rolling body damage, and the clearance increased. In the process of knocking the copper bar, the copper powder flew into the bearing cage, which was easy to cause the bearing fault.

8. Wear caused by high temperature

The hardness caused by abnormal high temperature, the metallographic structure or chemical composition of the metal change, which makes the wear resistance and hardness of the bearing surface reduce, and speeds up the wear process. This kind of wear is called wear caused by high temperature action. Wear caused by high temperature. When the bearing works temporarily under high temperature.

9. Too much oil causes the bearing rolling element to slip

Why are Your Bearing Parts Broken so Easily? Let’s Listen to What Professional Engineers Say about It 3

Too much oil in the bearing and the box will cause the bearing rolling body to slip, which will cause the rolling body to change from rolling friction to sliding friction and damage the bearing rolling body. Due to too much oil in the bearing box, the free space in the bearing box is small, the operating temperature of the bearing will rise, the speed of the lubricating grease will decrease, the lubricating oil film of the rolling body will become thin, the lubricating conditions are poor, and it is easy to cause the bearing noise, the surface sliding and the shortening of the bearing life. Generally, the motor end cover side is equipped with bearing oil chamber (except for the motor designed as double sealed bearing). According to the speed of the motor, the amount of oil that can be injected into the bearing chamber can refer to the following standards: when the speed of the motor is less than 1500r / min, the oil filling amount is 2 / 3 of the volume of the bearing chamber. When the rotating speed is between 1500-3000r / min, it is 1 / 2 of the bearing chamber volume. When the rotating speed is more than 3000r / min, it should be less than or equal to 1 / 3 of the bearing volume. In the actual working process, for the bearings operating at high temperature and high speed, the bearing with sealing surface should be used as little as possible, the oil storage of motor oil cover should be increased, and the oil nozzle should be installed, which can improve the operating life of motor bearings.

10. For the bearing with outer ring insulation design, pay attention to ensure that the insulation is intact

If the bearing insulation is damaged during installation, the very thin bearing oil film will be broken down by the shaft voltage. After the oil film breaks down, not only the lubrication condition of the rolling element is bad, but also the electric spark generated will form electric erosion on the bearing rolling element, which will cause the surface of the rolling element not smooth and accelerate the wear of the bearing.

Bearing position wear can be repaired in this way. The solution is: it is necessary to re study the use conditions or re select the bearing, observe the clearance and check the machining precision between the shaft and the bearing strip, check the design around the bearing, study and check the methods of installation, lubricant and lubrication.

成人免费黄色在线网站-日韩精品一区二区三区四区在线| 欧美黄色三级视频网站-国产九九热视频在线观看| 免费av一区在线观看-国产精品视频高潮流白浆视频免费| 91亚洲美女视频在线-熟妇人妻精品一区二区三区蜜臀| 色综合色综合久久综合频道-埃及艳后黄版在线观看| 91精品国产无线乱码在线-999精品视频免费看| 亚洲精品激情一区二区-久久成人国产欧美精品一区二区| 欧美精品啪啪人妻一区二区-嫩草人妻舔舔羞羞一区二区三区| 男人的天堂久久精品激情-最新亚洲精品a国产播放| 免费午夜福利在线观看-黄色日本黄色日本韩国黄色| 日本高清二区视频久二区-大香蕉在线视频大香蕉在线视频| 一级小黄片在线免费看-亚洲欧美午夜情伊人888| 国产小黄片高清在线观看-涩涩鲁精品亚洲一区二区| 欧美精品国产白浆久久正在-国产精彩视频一区二区三区| 日韩中文字幕v亚洲中文字幕-日韩亚洲av免费在线观看| 中文字幕偷拍亚洲九色-亚洲视频不卡一区二区天堂| 国产剧情av中文字幕-五月婷婷在线手机视频| 99在线免费观看视频-丰满人妻一区二区三区视频53| 三级a级一级大片在线观看-日韩av有码免费观看| 青青草原免费国产在线视频-精品人妻乱码一区二区三区四区| 看肥婆女人黄色儿逼视频-秋霞电影一区二区三区四区| 99热在线精品免费6-av一区二区在线观看| 久久精品亚洲国产av久-国产精品视频一区二区免费| 国产成人精品免费视频大全办公室-亚洲欧美日本综合在线| 激情字幕久久久字幕中文-一区二区三区免费黄片| 夜夜久久国产精品亚州av-欧美大屁股一区二区三区| 成人av一区二区蜜桃-亚洲色图激情人妻欧美| av中文字幕男人天堂-懂色av一区二区三区在线观看| 国产在线观看高清精品-四季av一区二区三区中文字幕| 国产在线一区二区三区欧美-久久偷拍精品视频久久| 欧美日韩亚洲1区2区-黄污视频在线观看不卡| 国产欧美日韩中文字幕在线-国产伊人一区二区三区四区| 欧美日本亚一级二级三区久久精品-日韩欧美一区二区久久婷婷| av中文字幕男人天堂-懂色av一区二区三区在线观看| 五月婷婷免费观看视频-男人操女人下面视频在线免费看| 欧美日韩精品人妻在线-在线播放中文字幕一区| 国产成人精品亚洲精品密奴-国产成人AV无码精品| 五月婷婷六月在线观看视频-亚洲黑寡妇黄色一级片| 精品亚洲卡一卡2卡三卡乱码-一区三区二插女人高潮在线观看| 99在线观看精品视频免费-国产极品一区二区三区四区| 欧美精品一区二区不卡-精品国产一区二区三区香蕉网址|