欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

Milling process is essentially a kind of intermittent processing process. This causes the temperature at the cutting edge to fluctuate between high temperature (about 1000 ℃) and low temperature.

Effect of cutting fluid

When the cutting edge cuts in and cuts out, the temperature change will increase. As a result, the cutting edge is subject to thermal shock and periodic stresses, which may result in cracks and, in the worst case, premature end of tool life.

The higher the temperature of the cutting area, the less suitable the cutting fluid is.

In the finishing process, the use of cutting fluid will not shorten the tool life as much as in rough machining due to the reduced heat generated.

When to Use Wet Milling or Dry Milling? 2
Hot cracks on cutting edge

dry milling

Dry milling can prolong the life of cutting edge. The temperature does change, but it will remain within the design range of cemented carbide materials.

Rough milling should always be carried out without cutting fluid.

wet milling with cutting fluid

There are some exceptions to the use of cutting fluid:

1) Finish machining of stainless steel and aluminum alloys – used to prevent metal particles from sticking to the surface structure

2) Milling superalloys at low cutting speeds – for lubrication and cooling of parts

3) Cast iron milling, used to wet and remove dust to protect the environment and health and ensure the accuracy of parts

4) Milling of thin wall parts to prevent geometric deformation

5) When machining deep cavity, micro lubrication system (i.e. compressed air containing a small amount of special oil) can be used to assist chip removal

When to Use Wet Milling or Dry Milling? 3
Use compressed air and oil mist

In the micro lubrication system, the “oil mist” is only a few milliliters of oil per hour, and is discharged through the ordinary filtering ventilation system.

When to Use Wet Milling or Dry Milling? 4
Use a large flow of internal and external coolant

If wet milling must be carried out, a sufficient amount of cutting fluid should be used.

久久无码免费视频| 国产成人无码AV一区二区三区| 熟妇人妻无乱码中文字幕| 国产品无码一区二区三区在线| 欧美精品日韩精品中文字幕| 鸡巴插进缝里 日本| 中文字幕你懂的av一区二区| 国产成人精品久久久成人| 日国产精品1卡二卡三卡| 毛片日产av一区二区三区四区| 白虎鲍鱼抠逼免费看| 国产老妇伦国产熟女91| 国产尤物蜜臀AV| 亚洲大尺度无码无码专线一区| 欧美大鸡巴操穴日韩| 国产亚洲一区白丝在线观看| 欧美精品国产一区二区在线观看| 美女麻豆颜色光屁股眼子| 日本黑鸡吧黄色录像| 大胸瑟瑟黑丝午夜| 欧美国产人妖另类色视频| 国产精品一区二区日本欧美| 99久久99久久精品视频| 骚逼嫩鸡巴喷水视频| 男女边吃奶边做边爱视频| 一区二区三区 日韩在线| 操世界最美丽的逼片| 亚洲大尺度无码无码专线一区| 欧美亚洲干妞内射| 夫妻性生活在线免费视频| 亚洲综合极品香蕉久久网| 粉嫩小穴被大鸡巴操视频在线观看| 一级特一黄大片欧美久久| 外国处女BB视频| 蜜桃av噜噜一区二区三区免费| 可以免费看污污片的软件| 91成人精品国语自产拍| 最新中文字幕av不卡高清| 成人国产亚洲精品一区二| 强伦人妻一区二区三区视频18| 非洲男生操男生屁眼视频|