欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

At present, stainless steel is widely used in industry such as aerospace, power generation equipment manufacturing, construction and food. As a typical hard-to-machine material, stainless steel has the defects of severe hardening during processing, high cutting temperature and easy adhesion of chips. Due to the above characteristics of stainless steel, common problems such as accelerated wear of the tool, poor integrity of the machined surface, and difficulty in chip removal are likely to occur during the machining process of STS, which seriously affects the processing quality, production cycle and processing cost of those material parts containing STS. Meetyou carbide tech depart analyzes and summarizes the difficulties in processing stainless steel materials, and provides solutions with specific measures for stainless steel cutting and typical products for your reference.

Choosing Material for Machining Stainless Steel is Difficult? Let’s Hear the Expert Tips 1

Reasons why stainless steel materials are difficult to process

1. High temperature strength and work hardening tendency

Compared with ordinary steel, stainless steel has medium strength and hardness. However, it contains a large amount of elements such as Cr, Ni, and Mn, and has good plasticity and toughness, high temperature strength, and high work hardening tendencym which therefore result in the cutting load. In addition, in the austenitic stainless steel during the cutting process, some carbides are precipitated inside, which increases the scratching effect on the cutter.

Choosing Material for Machining Stainless Steel is Difficult? Let’s Hear the Expert Tips 2

Fig.1. Common stainless steel’s temperature strength

2.Large cutting force is required

Stainless steel has large plastic deformation during cutting, especially austenitic stainless steel (the elongation exceeds 1.5 times that of 45 steel), which increases the cutting force.

3.chip and tool bonding phenomenon is common

It is easy to form built-up edge during cutting, which affects the surface roughness of the machined surface and easily causes the surface of the tool to peel off.

4. the chip is easy to curl and break

For closed and semi-closed chip cutters, chip clogging is easy to occur, resulting in increased surface roughness and tool chipping

Choosing Material for Machining Stainless Steel is Difficult? Let’s Hear the Expert Tips 3

Fig.2. The ideal chip shape of stainless steel

5. the large coefficient of linear expansion

It is about one and a half times the linear expansion coefficient of carbon steel. Under the action of cutting temperature, the workpiece is prone to thermal deformation and affects the dimensional accuracy.

6. small the thermal conductivity

Generally, it is about 1/4~1/2 of the thermal conductivity of medium carbon steel. The cutting temperature is high and the tool wears fast.

工具材料の選択

1. Tool materials with high hardness, toughness and heat resistance, and chemical affinity with stainless steel should be selected.
2. When using high-speed steel to process STS, high-performance high-speed steel such as W2Mo9Cr4VCo8, W6Mo5Cr4V2Al, W10Mo4Cr4V3Al, etc. should be used.
3.When using cemented carbide, it is not advisable to use YT-based alloys, and it is preferable to use Ta (Nb)-containing YW or YG tungsten-cobalt (ISO M, K) alloys. Such as YS2, YG3X, YG8W, YG6A, YG6X, YG643, YG813, YW3Y, YG8N, etc.
It is well known that the cutting performance of tool materials is related to the durability and productivity of the tool. The processability of the tool material affects the manufacturing and sharpening quality of the tool itself. It is advisable to choose tool materials with high hardness, good adhesion resistance and toughness, such as YG type hard alloys.Using YT type hard alloys for SUS is not a good choice, especially in processing 1Gr18Ni9Ti austenitic stainless steel. YT type hard type should be absolutely avoided. Alloys, because titanium (Ti) in stainless steel and Ti in YT-based cemented carbides produce affinity, the chips easily carry away the Ti in the alloy, which leads to tool wear. Production practice stat shows that the processing of stainless steel with YG532, YG813 and YW2 produce good processing results.
Because cemented carbide has better heat resistance and wear resistance than high-speed steel, tools made of hard alloy materials are more suitable for stainless steel cutting. Tungsten-cobalt alloy has good toughness. The tool can be made with a larger rake angle and a sharper edge.So in general, it is suitable to process stainless steel with a tungsten-cobalt alloy. Especially in the case of rough machining and interrupted cutting with large vibration, tungsten-cobalt alloy blades should be used. It is not as hard and brittle as tungsten-cobalt-titanium alloy, and it is not easy to chip. While Tungsten-cobalt-titanium alloy has good red hardness and is more wear-resistant than tungsten-cobalt alloy under high temperature conditions, but it has high brittleness and is not resistant to impact and vibration. Thus, it’s generally used as a stainless steel finishing tool.

Choosing Material for Machining Stainless Steel is Difficult? Let’s Hear the Expert Tips 4

Fig.3. Comparison of YT grade and YG grade
4.The coatings of cemented carbide may be CA15, CA25, YBM151, YBM251, YBM351, YBG202, YBG252, YBG302, CN251, YB425, ZC05, ZC07, ZM10 and the like.
The classic coating is a TiAlN or AlCrN coated tool. TiAlN coating has excellent properties such as high hardness, high oxidation temperature, good thermal hardness, strong adhesion, low friction coefficient and low thermal conductivity. Since the Cr element has a higher melting point than the Ti element, the coating company has developed an AlCrN coating in which Cr is substituted for Ti. Compared with TiAlN, the high temperature oxidation temperature of AlCrN can be significantly improved, the friction coefficient is smaller, the chip removal ability is stronger, but the hardness is slightly reduced.

Choosing Material for Machining Stainless Steel is Difficult? Let’s Hear the Expert Tips 5

Fig.4 The comparison of hardness of 3 different coating material
For cermet, YNG151 can be used. For coated cermet YNG151C can be used.

コメントを殘す

メールアドレスが公開(kāi)されることはありません。 が付いている欄は必須項(xiàng)目です

国产裸模大尺度私拍视频| 久久久久久久 亚洲精品| 两个人免费视频高清| 骚逼毛茸茸乱伦视频| 国产三级精品久久久久| 亚洲欧美日韩清纯唯美第一区| 亚洲国产日韩欧美高清片| 9亚洲导航深夜福利亚洲| 美女荒郊野外找男人靠逼| 国产精品亚洲一区二区三区下载| 69国产精品久久久久久人| 美女穿黑丝被大鸡巴猛操| 一区二区三区四区五六区| 大鸡巴操饿罗斯女人| 国产精品操大屁股老淑女| 国产精品三级一区二区| 欧美男女舔逼舔鸡巴视频| 国产一区二区三区午夜精品久久| 鸡巴插骚逼真舒服| 欧美精品第15页| 日本公共厕所mmm撒尿| 粉色av一区二区三区| 久久久久九九九国产精品| 大黑鸡巴操模特骚B| 公交车上被后入搞逼漫画| 东北大吊干东北少妇AV| 我想看操小嫩逼大片| 91成人精品国语自产拍| 娇嫩的被两根粗大的np| 中文字幕欧美人妻在线| av人摸人人人澡人人超| 日韩 欧美 成人 免费| 日本亚洲免费不卡| 亚洲男性天堂一区二区三区| 黄网官方在线观看| 3色w九九久久男人皇宫宕| 亚洲欧洲日本精品| 日本乱人伦中文在线播放| 无码中文字幕免费一区二区三区| 国产精品免费第一区二区| 丝袜片一区二区三区四区五区|