欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

Many customers complain that the service life of cemented carbide molds they buy is very short, and they often crack after less than oneortwo times of stamping. That’s because first of all, cemented carbide is a hard but brittle material, and special attention should be paid to the maintenance of cemented carbide molds in use. Secondly, customers usually haven’t considered these three aspects. Today we will share with you in an article how to extend the service life of your cemented carbide mold through these three points.

3 ASPECTS DETERMINE THE SERVICE LIFE OF YOUR CEMENTED CARBIDE MOLD 2

Have you selected cemented carbide molds with a good quality? ?

Quality includes the following:

1. It must have high resistance: the mold must accept great extrusion pressure, bending stress, impact and other messy loads at the same time during the extrusion process.

2. It must have very good wear resistance: the mold should have high wear resistance to ensure normal service life and produce a large number of qualified extrusions.

3. There must be sufficient thermal stability: during each continuous production, the temperature rise of the mold sometimes reaches or exceeds 200 ℃, which will reduce the strength and hardness of the mold material with 160~180 ℃ as the tempering temperature. Therefore, the mold material with higher temperature rise should have excellent tempering stability.

4. It must have outstanding technicality: the manufacturing cycle of cold extrusion die is long, the technology is messy, and the accuracy requirement is high. Generally, casting, cutting, heat treatment, grinding or other finish machining are required.

Do you use cemented carbide for production correctly?

When using cemented carbide dies, we should pay attention to the following points:

1. During the working process of the machine and equipment, the technician monitors the working condition of the equipment in real time to eliminate the machine faults in advance. Only in this way can we ensure the smooth progress of the whole production process.

2. The cemented carbide mold must be in a safe state before it is used and in the process of idle parking.

3. Cemented carbide dies belong to high maintenance rate equipment because of long-term load work. During maintenance, the machine should be firmly fixed with supports, the equipment should be shut down, and the whole set of equipment should be in a static state before starting the next step of maintenance work.

4. The gear oil in the cemented carbide mold is very irritating to the skin. When checking whether there is leakage, don’t touch it with your hands. If necessary, wear gloves or use paper to check, so as to avoid direct skin contact. Different cemented carbide molds need to be careful in the processing process, with safety as the main factor.

5. Select the appropriate reduction ratio. Cemented carbide die itself has the characteristics of hardness and brittleness. If it is used for shrinkage drawing with large area shrinkage, it is easy to cause the die to bear the stress and be broken and scrapped. Therefore, it is necessary to select the appropriate area shrinkage according to the different mechanical properties of wire rod.

3つの側(cè)面が超硬合金の耐用年數(shù)を決定します3

Do you regularly repair your cemented carbide mold?

Regular maintenance of cemented carbide dies is a major factor that can effectively improve the service life of cemented carbide dies.

For example, the installation and debugging method of the mold should be appropriate. In the case of hot runner, the power wiring should be correct, the cooling water path should meet the design requirements, the parameters of injection molding machine, die casting machine and press machine should meet the design requirements in the production of the mold, etc.

When using the mold correctly, it is also necessary to maintain the mold regularly. The guide post, guide sleeve and other parts with relative movement of the mold should be often filled with lubricating oil. For forging mold, plastic mold, die-casting mold and other molds, lubricant or molding agent should be sprayed on the surface of formed parts before each mold is formed.

The planned protective maintenance of the mold and the data processing in the maintenance process can prevent the problems that may occur in the production of the mold and improve the efficiency of maintenance work.

コメントを殘す

メールアドレスが公開されることはありません。 が付いている欄は必須項目です

色橹橹欧美在线观看视频高清免费| 西瓜在线看免费观看视频| 护士毛片在线看中文字幕| 性爱大鸡吧喷水视频| 亚洲欧洲精品无码久久久| 男女边吃奶边做边爱视频| 男生用鸡巴操女生的视频| ai换脸久久一区二区亚洲av| 亚洲综合无码一区二区丶| 欧美一区二区三区刘玥| 熟女大屁股亚洲一区| 国产成人亚洲欧美久久| 亚洲av 又黄又爽十大| 亚洲欧洲精品无码久久久| 中文字幕国产精品一区二区三区| 一区二区三区四区五六区| 黄色日女人逼视频| 狂插美女大屁股在线观看| 黑大吊肏小騷逼噴水| 伊人网在线视频观看| 美女的咪咪和骚逼| 日本高清不卡一区二区三区| 亚洲精品国产综合一线久久| 欧美一区二区三区久久国产精品| 日本六十五十熟女一级黄色| 免费人成再在线观看| 午夜场射精嗯嗯啊啊视频| 日本成人精品一区二区三区| 国奴精品毛片av一区二区三区| 看女生b免费视频| 成年女人永久看片视频 | 玩弄邻居少妇呻吟11p| 精品的极品美女一区二区三区| 亚洲 欧美 精品 高清| 亚洲午夜福利视频在线| 我想看操小嫩逼大片| 波多野吉衣一区在线观看| 在线观看国产黄色| 久久久久久高清无码视频| 骚女人被大吊干视‘| 久久久久久久久黄片观看|