欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

To reduce tool Build-Up and minimize the cost of tool wear during mass production, a combined theoretical and practical analysis approach is employed. This approach comprehensively examines the processing conditions, including processing efficiency, cooling methods, and material properties. It aims to address the issue of aluminum adhesion caused by aluminum melting, allowing for tool reuse and thus lowering tool consumption costs.

With the rapid development of China’s automotive industry, especially in the booming new energy vehicle sector, lightweighting has become a core topic. The key to lightweighting is changing traditional materials. Aluminum alloys, with their high strength and low weight, are essential for achieving vehicle lightweighting. The complex geometric shapes of automotive parts and the increasing proportion of die-cast aluminum alloy parts in vehicles have led to a growing demand for CNC machining of die-cast parts.

CNC machining of aluminum alloy automotive parts requires high efficiency, stable continuous production, and decreasing costs, necessitating more detailed control and planning of the entire production process.

How to Treat Tool Build-Up in Aluminum Alloy Cutting Processes Using Chemical Methods? 1

Tool Build-Up

Aluminum’s inherent property of low melting point causes it to become “sticky” during cutting. Due to this characteristic and inadequate cooling in actual conditions, the heat generated by friction during the microscopic cutting process cannot be released in time or effectively. This results in aluminum melting and adhering to the tool’s cutting edges and chip flutes. Upon cooling, the aluminum solidifies and sticks to the tool, forming build-up. This phenomenon, commonly referred to in the industry as “easy tool sticking,” leads to tool failure.

Tools are consumables in CNC machining processes and represent a significant cost component. Generally, cutting tools for aluminum alloys need to be sharper, with chip flutes specially polished and coated with aluminum-specific coatings to improve chip removal efficiency. The automotive industry’s push for high efficiency increases feed rates and cutting speeds, which raises the heat generated during cutting and the risk of aluminum melting and sticking to the tool, thereby increasing costs due to tool failure from build-up.

With environmental regulations, minimal quantity lubrication (MQL) is widely used as a cutting fluid alternative in aluminum alloy CNC machining. However, the low melting point of aluminum exacerbates the reduced cooling effect of MQL, further promoting build-up. Tools that fail due to sticking account for about 40% of conventional tool failures. Traditional methods of dealing with build-up, such as tapping or striking, rarely restore tools for reuse. Thus, a new solution is proposed.

Treatment Measures

The new solution involves the following steps:

  1. Remove the tool with build-up.
  2. Obtain solid NaOH, dilute it with water, and place it in a ceramic container.
  3. Once diluted into NaOH solution, immerse the tool with aluminum build-up in the solution. Ensure that the build-up areas are fully submerged and maintain immersion for 2 hours, or adjust based on practical conditions. Table 1 compares traditional and new treatment methods.
Traditional Treatment New Solution
Tools with aluminum build-up are discarded directly, leading to significant production costs Immersion liquid can remove aluminum from complex and irregular shapes
Physical methods like tapping and striking damage the polished surface, leading to tool discard or reduced cutting efficiency Short treatment time and simple operation
Short treatment time and simple operation Easy-to-obtain treatment materials with low cost

 Build-Up

Chemical Principles

Using A1Si7Mg material commonly found in automotive parts as an example, where A1 content is approximately 93.5%, Si content is 6.5%, and Mg content is 0.25%. Both Al and Si react with NaOH solution. Immersion in NaOH solution removes the primary A1 component from the tool. The principle involves the reaction between metal and NaOH, producing bubbles (H?), which eventually causes the adhered aluminum to detach.

Chemical reaction equations are as follows:

  1. Si reacts with NaOH: Si + 2NaOH + H?O → Na?SiO? + 2H?↑
  2. Al reacts with NaOH: 2Al + 2NaOH + 2H?O → 2NaAlO? + 3H?↑

The final result is the removal of aluminum, making the tool reusable.

Experimental Validation for Reducing Build-up

The theoretical method was tested using a tap. Taps are valuable tools in aluminum alloy machining, requiring a longer lifespan and featuring complex geometric shapes. Once aluminum adhesion occurs, physical removal is nearly impossible, making this test more significant and representative.

Due to high heat generated during machining and possible inadequate cooling, aluminum melts instantly and adheres to the flutes rendering the tap unusable due to damaged threads.

The test involved immersing the tap with aluminum build-up in NaOH solution.

The test conclusion: The tap, after complete immersion in NaOH, showed that the build-up had completely detached. Residual aluminum slag was found in the test container. The treated tap was used for further machining, and the workpiece threads met the required specifications. The tap was successfully restored for reuse.

How to Treat Tool Build-Up in Aluminum Alloy Cutting Processes Using Chemical Methods? 2

Conclusione

The automotive parts industry, characterized by mass production, requires extensive cutting validation during the initial equipment and tool design phase. Common issues such as build-up during validation due to parameter mismatches, equipment adjustments, and operator experience can significantly increase trial costs and production cycles. This method effectively addresses build-up issues, greatly reducing tool costs and processing time, extending tool life, and substantially lowering production costs.

Settembre 4, 2024

Perfect

Lascia un commento

Il tuo indirizzo email non sarà pubblicato. I campi obbligatori sono contrassegnati *

淫荡淫水逼操烂视频| 久操视频中文字幕在线观看| 午夜精品福利一区二区三区蜜桃p| 大鸡巴插我在线观看| 午夜国产三级一区二区三| 大屌把女生逼逼操肿国产| 国产亚洲一区白丝在线观看| 丰满少妇被强入在线观看| 日本不卡高清视频在线播放| av在线国产哟哟| 一区二区国产欧美日韩无| 黄色av成年人在线观看| 猛哥操女人B视频| 日韩成人伦理片在线观看| 国产 日韩 亚洲 一区| 美女插逼插出淫水来| 白嫩在线亚洲观看| 一级做a爱过程免费视频俩| 被下药强奷到舒服的视频| 男生和女人靠逼视频| 国产精品久久一区二区三区夜色| 内射后入在线观看一区| 嗯啊好大好想要视频| 最新黄色A级一短片| 国产高欧美性情一线在线| 强奷很舒服好爽好爽| 午夜性刺激在线视频免费| 久久精品欧美日韩精品不卡| 精品麻豆国产免费一区二区三区| 久久99热精品在线观看| 国产又粗又猛又色又免费| 美女被插进去黄色| 91啪国线自产2019| 国产一区二区三区精品片| 在线看免费无码a片视频| 国产精品无码毛片久久久| 欧美人与动人物A级| 日本高清一区二区三区不卡| 久久99国产中文| 欧美大鸡巴操穴日韩| 男插女逼啪啪啪软件|