欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

As a precision measuring tool, micrometer (also known as screw micrometer) is widely used in precision machining. It is well known by people in the industry. However, the measured value is not an absolute value. Only when the measuring tool is used correctly can it approach its accurate value infinitely.

The first step in using the micrometer correctly:

Micrometer can be divided into digital display type, mechanical type (non digital display), waterproof and oil proof type, general type, special type, large-scale, rapid measurement type, ultra-high precision type, etc. before use, it is necessary to carefully confirm the type, measurement range, accuracy or other specifications.

Reading scale correctly

In the use of mechanical micrometers (non digital display type), there are often errors in reading, which affect the accuracy of measurement. It is very important to master the reading mode of scale and improve the accuracy of reading.

Do You Really Know How to Use Micrometer? 2

When reading the reticle of the differential cylinder, the correct posture is to look directly at the reference line. As shown in the following example:

Reading the scale of standard micrometer

Do You Really Know How to Use Micrometer? 3

Standard micrometer:

Do You Really Know How to Use Micrometer? 4

In general, the division value 0.01mm can be read as shown in the figure above, or 0.001mm can be read as shown in the figure below.

Scale reading with vernier micrometer

With cursor (index value 0.001mm):

Do You Really Know How to Use Micrometer? 5

Micrometer with vernier refers to the vernier scale on the base line of casing.

Note: when the leader is between two scales (as shown in positions ②, 21 and 22), it is read as 0.21mm.

When the stroke scale is aligned with one of the micro scales (as shown in Fig. position ③), the reading is 0.003 mm.

Effect of temperature

Before measurement, in order to avoid the influence of temperature, the micrometer and the workpiece to be measured shall be placed at room temperature for a long enough time to make its temperature balanced.

However, in the process of using micrometer, the influence of hand temperature on micrometer is often ignored.

Do You Really Know How to Use Micrometer? 6

When measuring with a micrometer, the heat of the hand will be transferred to the measuring tool when the hand is holding the micrometer frame, resulting in obvious measurement error (as shown in the following experimental results).

As shown in the figure above, the thermal expansion value of the micrometer increases with the holding time.

Thus,

① If the micrometer must be held during measurement, the contact time shall be minimized.

② To reduce the above temperature effects, you can also choose to install a thermal insulator or wear a pair of gloves.

③ Special micrometer stand can be selected.

The influence of support platform

When using the bench, the choice of fulcrum position and the posture of micrometer have different effects on the measurement results. As shown in the chart below. Therefore, after determining the measurement pose, it is necessary to align the base point for reuse.

Other general precautions

The starting point (zero) should be adjusted before measuring, and zero position should be used before using the non fuzzed paper to wipe the measuring surface of the anvil and the micro screw.

Do You Really Know How to Use Micrometer? 7

As part of daily maintenance, wipe off any dust, debris and other debris around the environment and on the measuring surface. In addition, carefully wipe any stains and fingerprints with a dry cloth.

Use the force measuring device correctly, so as to measure under the correct force. Note: when the measuring surface contacts the workpiece and the subsequent measurement, the force measuring device must be used to prevent the workpiece from being impacted rapidly.                             

When the micrometer is installed on the micrometer stand, the stand shall be fixed and clamped in the center of the micrometer frame. But don’t clamp it too tightly.

Do You Really Know How to Use Micrometer? 8

Take care that the micrometer does not fall or collide with anything. Do not use excessive force to rotate the micrometer micro screw. If it is felt that the micrometer may have been damaged due to accidental misoperation, its accuracy needs to be further checked before use.

After a long period of storage or protective oil film, wipe the micrometer gently with a cloth soaked in anti-corrosion oil.

Precautions for storage

△ avoid direct sunlight during storage.

△ store in a place with good ventilation and low humidity.

Store in a place free of dust.

△ if it is stored in a box or other container, the box or container cannot be placed on the ground.

△ during storage, there should be a gap of 0.1mm to 1mm between the measuring surfaces.

△ do not store the micrometer in the clamped state.

Lascia un commento

Il tuo indirizzo email non sarà pubblicato. I campi obbligatori sono contrassegnati *

国奴精品毛片av一区二区三区| 人妻少妇精品视频12p| 亚洲中文字幕在线无码一区二区| 欧美在线A片一区二区三区| 国产精品熟女一区二区三区久久夜| 色逼色逼色逼色逼色逼色| 欧美大鸡巴操大骚逼| 国产精品白浆一区二区三区| 日本免费暖暖在线小视频| 91啪国线自产2019| 福利国产第一视频| 亚洲AV无码一区二区三区天堂古| 男女真人牲交高潮全过程| 鸡巴和逼中国美女| 欧美性做爰片免费视频看| 看一下日本人插逼逼洞视频| 国产妇女乱一性一交| 五月天国产成人av在线| 国产一区二区在线观看精品| av中文字幕一区二区精品久久| 美女嫩逼插进大屌| 色一情一交一乱一区二区| 亚洲女同一区二区三久久精品| 日本免费一区二区在线| 国产成人精品区在线观看| 插逼爽歪歪视频免费| 三上悠亚精品一区二区久久| 国产一区二区在线观看精品| 亚洲Av无码专区一区二区三区| 国产亚洲欧美日韩在线观看一区| 被几个大屌老外轮操| 美女的粉嫩小逼视频特写| 日韩毛片一区视频免费在线观看| 正在播放 国产精品推荐| 99久久久国产精品美女| 久久久久有精品国产麻豆| 国内精品久久久久精品97| 精品免费久久久久久久久| 美女日逼视频免费| 日韩人妻无码中字一区二区| 老熟妇高潮一区二区高清视频|