欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

The difference between u-drill and ordinary drill is that u-drill uses blades – peripheral blade and central blade. From this point of view, the relationship between u-drill and ordinary hard drill is almost the same as that between machine clamp turning tool and welding turning tool. After the u-drill is worn, the blade can be replaced directly without regrinding.

How to Avoid Malfunction of Carbide U Type Drills 2

After all, the use of indexable blade is still less material than the whole hard drill, and the consistency of blade is easier to control the size of parts. So, u drill is a good choice for you!

U-drill can drill holes on the surface with inclination angle less than 30 ° without reducing cutting parameters.

When the cutting parameters of u-drill are reduced by 30%, intermittent cutting can be realized, such as intersecting hole, intersecting hole and perforating hole.

U-drill can drill multi-step holes, and can bore, chamfer, eccentric drilling.

When u drilling, most of the cuttings are short, and the internal cooling system can be used for safe chip removal without cleaning the cuttings on the tool, which is conducive to the continuity of product processing, shorten the processing time and improve the efficiency.

Under the condition of standard length diameter ratio, there is no need for chip removal when u drill is used.

U-drill is a indexable tool, which does not need to be sharpened after the blade is worn. It is convenient to replace and has low cost.

The surface roughness value of the hole processed by u-drill is small and the tolerance range is small, which can replace the work of some boring cutters.

The u-drill does not need to drill the center hole, and the bottom surface of the blind hole is relatively flat, so the flat bottom bit is omitted.

The use of u-drill technology can not only reduce the number of drilling tools, but also save a lot of time for grinding and tool replacement, which can improve the work efficiency by 6 ~ 7 times.

Common problems of u drill

Blade damage is too fast, easy to break, processing costs increase.

The cutting state is not normal due to the harsh whistling during machining.

The machine tool shakes, which affects the machining accuracy of the machine tool.

Key points for using u-drill

The installation of u drill should pay attention to the positive and negative directions, which blade is up, which blade is down, which face is inside and which face is outside.

The center height of u-drill must be corrected, and the control range is required according to its diameter, which is generally controlled within 0.1 mm. The smaller the diameter of u-drill, the higher the center height requirement. If the center height is not good, the two sides of u-drill will be worn, the hole diameter will be too large, the service life of blade will be shortened, and small u-drill is easy to break.

The u-drill has a high requirement for coolant. It is necessary to ensure that the coolant is ejected from the center of the u-drill. The greater the pressure of the coolant, the better. The redundant outlet of the turret can be blocked to ensure the pressure.

The cutting parameters of the u-drill are strictly in accordance with the manufacturer’s instructions, but the blade of different brands and the power of the machine tool should also be considered. During the processing, the load value of the machine tool can be referred to for appropriate adjustment. Generally, high speed and low feed are used.

The u-drill blade should be inspected frequently and replaced in time. Different blades should not be installed reversely.

The feed is adjusted according to the hardness of the workpiece and the length of the tool overhanging. The harder the workpiece is, the larger the tool overhanging is, and the smaller the tool feed should be.

Do not use excessive wear blade, should be recorded in production blade wear and the number of workpieces can be processed, timely replacement of new blade.

Use sufficient and correct internal coolant pressure. The main function of coolant is chip removal and cooling.

U drill can not be used to process soft materials, such as copper, soft aluminum, etc.

How to Avoid Malfunction of Carbide U Type Drills 3

Technics of using u-drill in CNC machine tools

  1. When u-drill is used, it has higher requirements on the rigidity of machine tool and the neutrality of tool and workpiece, so u-drill is suitable for high-power, high rigidity and high speed CNC machine tools.
  2. When using u-drill, the central blade should be tough and the peripheral blade should be sharp.
  3. When machining different materials, different groove type inserts should be selected. Generally, when the feed is small, the tolerance is small and the length diameter ratio of u-drill is large, the groove type inserts with smaller cutting force should be selected. Otherwise, when the rough machining, tolerance is large and the length diameter ratio of u-drill is small, the groove type inserts with larger cutting force should be selected.
  4. When using the u-drill, we must consider the spindle power of the machine tool, the clamping stability of the u-drill, the pressure and flow of the cutting fluid, and control the chip removal effect of the u-drill, otherwise the surface roughness and dimensional accuracy of the hole will be greatly affected.
  5. When clamping the u-drill, make sure that the center of the u-drill coincides with the center of the workpiece and is perpendicular to the surface of the workpiece.
  6. When u drill is used, appropriate cutting parameters should be selected according to different parts materials.
  7. When cutting with u-drill, do not reduce the feed rate or rotate speed at will because of being careful and afraid, so as to damage the u-drill blade or the u-drill.
  8. When u-drill is used for machining, if the blade is worn or damaged, carefully analyze the reasons and replace the blade with better toughness or wear resistance.
  9. When u-drill is used to process stepped holes, it is necessary to start from large holes and then small holes.
  10. When using the U drill, pay attention to that the cutting fluid should have enough pressure to flush out the chips.
  11. The blades used in the center and edge of u drill are different. Do not use them wrongly, otherwise the U drill rod will be damaged.
  12. When u drill is used for drilling, workpiece rotation, tool rotation and tool and workpiece rotation at the same time can be adopted. However, when the tool moves in linear feed mode, the most commonly used method is workpiece rotation.

Leave a Reply

Your email address will not be published. Required fields are marked *

国产精品视频一区二区三区分享| 美女被操的流水AV| 69国产精品久久久久久人| 伊人久久综合无码成人网| 性一交一子一伦一乱| 亚洲人成在线不卡网| 九九视频免费在线观看| 青青操成人版性视频| 嗯啊好大好想要视频| 美女日比视频播放| 差鸡巴没码在线观看| 女生小穴色色视频| 精品一二三四区中文字幕| 公交车上被后入搞逼漫画| 免费观看的黄视频一级国产| 欧美人人做人人爽人人喊| 农村胖肥胖女人操逼视频| 日本不卡高清视频在线播放| a一级毛片免费高清在线| 日韩亚洲AV无码一区二区不卡| 成人高清在线播放一区二区三区| 欧美一区二区三区身体| 色噜噜人妻丝袜中文字幕| 亚洲午夜福利视频在线| 日本成人在线一区中文字幕| 福利国产第一视频| 国产一区二区三区在线观| 国产激情内射免费精品| 怎么样操女人的逼亚洲Av黄片段| 少妇被黑人入侵在线观看| 国产一区精品在线| 99精品一级欧美片免费| 婷婷6月天丁香综合在线| 欧美日韩久久久久久久久| 亚洲Av无码专区一区二区三区| 又爽又粗又大又长的爆草| 亚洲女同一区二区三久久精品| 久久久三级黄片免费视频| 久久综合娱乐中文网| 淫荡扣逼骚逼视频| 国产精品久久一区二区三区动|