欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

Surface roughness is an indicator used to measure the degree of surface micro-irregularities, and it is commonly annotated on mechanical drawings with roughness symbols. The types of roughness symbols include surface roughness symbols, roughness codes, and additional descriptions. The following is a detailed introduction to the types of roughness annotations.

Figure 1. Schematic of roughness surface profile hatching.

Surface Roughness Symbol

4 Points of Machining Surface Roughness You Need to Know 1

4 Points of Machining Surface Roughness You Need to Know 2

a?、a?— symbols and values for the roughness height

parameters (unit is μm);

b — machining requirements, plating, coating, surface treatment, or other descriptions;

c — sampling length (in millimeters) or waviness (in micrometers);

d — symbol for the direction of the machining texture;

e — machining allowance (in millimeters);

f — roughness spacing parameter (in millimeters) or profile support length ratio.

?Other Annotation Descriptions

  • Sampling Length: The length range selected when measuring roughness, used to calculate roughness parameters.
  • Evaluation Length: The total sum of the sampling lengths, used to assess surface roughness.
  • Machining Method: Indicates the machining method by which the surface roughness is achieved, such as turning, grinding, etc.
  • Other Requirements: For example, surface treatment (such as sandblasting, polishing, etc.), texture direction, etc.
Machining Texture Requirements
Machining Texture Requirements

4 Points of Machining Surface Roughness You Need to Know 34 Points of Machining Surface Roughness You Need to Know 4

Roughness Code

Arithmetic Mean Roughness Ra

Arithmetic mean roughness is the most commonly used roughness parameter, representing the arithmetic average of the absolute values of the profile peaks and valleys within the sampling length. When selecting the reference length in the direction of the mean line from the roughness curve, using the direction of the mean line of the selected part as the X-axis and the direction of the vertical magnification as the Y-axis, if the roughness curve is represented as y=f(x), the value obtained from the following formula, when expressed in micrometers (μm), is called the arithmetic mean roughness Ra.

4 Points of Machining Surface Roughness You Need to Know 5

Arithmetic Mean Roughness Ra

Note: The arithmetic mean roughness Ra is the most commonly used expression for roughness. Unless otherwise specifically noted, roughness generally refers to Ra.

From the roughness curve, a reference length is selected in the direction of the mean line. From the values measured in the direction of the vertical magnification from the mean line of the selected part, the sum of the average absolute values of the peak elevations (Yp) from the highest peak to the fifth peak and the average absolute values of the valley elevations (Yv) from the lowest valley to the fifth valley is calculated. This sum is referred to as the value expressed in micrometers (μm).

Ten-Point Average Roughness Rz
Ten-Point Average Roughness Rz

Maximum Height Ry

The maximum profile height, which represents the vertical distance between the highest profile peak and the deepest valley within the sampling length. From the roughness curve, a reference length is selected in the direction of the mean line. The interval between the peak line and the valley line of the selected part is measured in the direction of the vertical magnification of the roughness curve, and this value is called the micrometer value (μm).

Note: When determining Ry, the reference length should be selected from a section of the curve that is free of cracks and extreme peaks and valleys.

Maximum Height Ry
Maximum Height Ry

Labeling Example

Label the upper limit value of Ra

4 Points of Machining Surface Roughness You Need to Know 6

  • Control the surface roughness to within 25μm by any means.
  • Control the surface roughness to within 6.3μm by material removal methods.
  • Control the surface roughness to within 25μm without removing material.

Label the direction of the machining texture

4 Points of Machining Surface Roughness You Need to Know 7

Note: The direction of the machined tool texture is perpendicular to the projection plane marked with symbols.

Label the upper and lower limits of Ra

4 Points of Machining Surface Roughness You Need to Know 8

Control the surface roughness to a minimum of 1.6μm and a maximum of 6.3μm by removing material. Generally, the upper and lower limit values are marked for oil seal installation holes, as roughness that is too large or too small can affect the sealing effect of the oil seal.

Label the machining methodsurface roughness

Marking Machining Method

Attention Points Marking Position: The roughness symbol is usually annotated above or below the dimension line, close to the surface being marked.

Direction Guide Line: The direction guide line should point towards the surface being marked and be parallel or perpendicular to the surface.

Value Unit: The roughness values are typically expressed in micrometers (μm).

Laisser un commentaire

Votre adresse de messagerie ne sera pas publiée. Les champs obligatoires sont indiqués avec *

欧美黑屌操B内射冒白浆| 欧美国产三级片久久高清| 操老女人大逼视频| 国产成人精品久久久成人| 久久国产亚洲高清| 操逼啊 啊 啊黄色视频| 乱伦美女小骚货视频| 色偷偷影音先锋男人av| 欧美 日韩 激情 在线| 日本中文字幕无人区一区二区| 中文字幕乱码一区二区三区麻豆| 久久精品国产亚洲av伦理| 非洲男生操男生屁眼视频| 国产伦精品一区二区三区视频抖音| 白虎美女被大基吧操| 国产 欧美 日韩 黄片| 操我好舒服用力视频| 非洲男生操男生屁眼视频| 中文字幕一区二区 在线| 在线看免费无码a片视频| 亚洲欧洲精品无码久久久| 爆乳喷奶水无码正在播放| 大波美女被插的好爽| 免费看黑人操逼视频| 亚洲中文字幕在线无码一区二区| 99草草视频在线精品| 午夜精品福利一区二区三区蜜桃p| 亚洲欧美一区二区三区在| 欧美亚洲综合一区二区三区| 最新AV中文字幕在线看| 国产精选三级在线观看| 亚洲欧洲日本精品| 8050午夜三级的全黄| 日韩人妻精品一区二区三区99| 2021最新热播国产一区二区| 热精品韩国毛久久久久久| 男人草女人的视频免费看| 日韩美女叉B视频| 欧美国产日韩a欧美在线| 两人爽爽爽无码免费视频| 久久久精品国产乱码内射|