欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

Currently, TiN is the primary coating used for coated cutters, but traditional nitride coatings (such as TiN) have lower hardness, poor wear resistance, and especially poor thermal stability, which limits their application in dry cutting tools. In this paper, the researchers prepared TiN, TiAlN, TiN-MoS?, and CrTiAlN composite coated cemented carbide cutters using unbalanced magnetron sputtering technology. Comparative cutting tests were conducted on TiN and its composite coated cutters under dry cutting conditions. The study of the mechanical properties and cutting performance of TiN-based composite coated cutters is of great significance for the further development and promotion of coated cutters.

 

Experimental Method

TiN, TiAlN, TiN-MoS?, and CrTiAlN composite coatings were deposited on YT14 cemented carbide cutters using a closed-field unbalanced magnetron sputtering ion plating equipment from Teer Company. The nano hardness and elastic modulus of the coatings were measured using a Nano Test 600 nano hardness tester. To reduce experimental errors, the hardness and elastic modulus values were the average of five measurements. The hardness of the coatings was also verified using a Vickers microhardness tester, and the morphology and phase structure of the cutter coatings were observed and analyzed using a Quanta 200 scanning electron microscope (SEM) and an Advance 8 X-ray diffractometer (XRD). The cutting tests of the coated cutters were conducted on a CNC machining center, with PCNiMoVA steel as the cutting material. The flank wear was observed and measured using a 30x tool microscope. The cutting time when the wear strip width on the flank face exceeded 0.6mm was used as the basis for evaluating the tool’s life, and the cutting life of the tools was compared.

 

Experimental Results and Analysis

Coating Hardness and Elastic Modulus Testing

Figure 1 shows the loading and unloading curves obtained during the nano hardness measurement process of the CrTiAlN composite coating. The loading and unloading curves not only provide the hardness of the CrTiAlN film but also its elasticity. Define R = (ha – h) / h as the elastic recovery coefficient, where ha is the indentation depth at maximum load, and h is the residual depth of the indentation after unloading. According to the definition of R, the greater the value of R, the greater the elasticity of the film. Therefore, based on the nano indentation curve in Figure 1, the hardness of the CrTiAlN film is 33 GPa, and the elastic modulus is 675 GPa. Figure 2 is a comparative analysis chart of the nano hardness of TiN, TiAlN, TiN-MoS?, and CrTiAlN coatings. It can be seen from the figure that the nano hardness measurement values of the four coatings are 18 GPa, 30 GPa, 15 GPa, and 33 GPa, respectively. The nano hardness ranking is as follows: CrTiAlN > TiAlN > TiN > TiN-MoS?.

How to Enhance Mechanical Properties of TiN-Based Coated Cutters 2

How to Enhance Mechanical Properties of TiN-Based Coated Cutters 3

Figure 3 shows the measured elastic modulus values of each coating. It can be seen from the figure that the elastic modulus of the four coatings are 214 GPa, 346 GPa, 164 GPa, and 675 GPa, respectively. The ranking of the elastic modulus is as follows: CrTiAlN > TiAlN > TiN > TiN-MoS?. This indicates that the elastic modulus of the coatings is directly proportional to their hardness. However, the CrTiAlN coating shows the greatest relative increase in elastic modulus, with a value significantly higher than other coatings, reaching 675 GPa, which suggests that the deposited CrTiAlN coating has both high hardness and high elasticity.

Meanwhile, the Vickers microhardness tester was used to perform microhardness verification tests on each cutter coating, with a indentation load of 15g and a duration of 10 seconds. The measurement results are shown in Figure 4. By comparing the coating nano hardness in Figure 2 with the coating microhardness values in Figure 4, it can be found that the microhardness variation trend of each coating is the same as the nano hardness variation trend, with the CrTiAlN coating having the relatively highest Vickers microhardness at HV1560.

 

Analysis of Coating Surface Morphology

The surface morphologies of the TiN, TiAlN, TiN-MoS?, and CrTiAlN coated cutters are shown in Figure 5. It can be observed from the figure that there is a significant difference in the surface morphology of the four coatings, indicating that the addition of composite elements has caused a great change in the crystalline state of the TiN compounds. Among them, the TiN coating surface phase tissue is uniform, with relatively fine particles, while the TiAlN coating surface morphology is relatively rough, with coarser particle tissue. The TiN-MoS? coating surface is distributed with a large amount of flaky mixed structure, mainly due to the uniform distribution of MoS? phase in the TiN coating, tending towards a composite structure in the mixed state, which serves a self-lubricating function. The CrTiAlN coating surface grains are relatively fine, the coating is dense and uniform, and the surface is distributed with a large number of hard points.

How to Enhance Mechanical Properties of TiN-Based Coated Cutters 4How to Enhance Mechanical Properties of TiN-Based Coated Cutters 5

Drilling Test

The four types of coated cemented carbide cutters were used to machine PCNiMoVA steel, and the wear condition of the cutters was inspected to compare the durability of different coated cutters.

The cutting test conditions for the coated cutters were as follows: the cutting method was external cylindrical cutting, the cutting speed was 160 m/min, the feed rate was 0.15 mm/r, the cutting depth was 0.5 mm, and dry cutting was performed. The cutting time when the wear strip width on the flank face exceeded 0.6 mm was used as the basis for evaluating the tool’s life, and the cutting life of the tools was compared.

A comparison of the cutting life of the coated cutters is shown in Figure 6.

From the figure, it can be seen that under dry cutting conditions, the cutting life of the uncoated cutters was the shortest, and the service life of the coated cutters was significantly better than that of the uncoated cutters. Among them, the CrTiAlN coated cutter had the longest cutting life. The ranking of the cutting life of the four coated cutters was as follows: CrTiAlN > TiN-MoS? > TiAlN > TiN. This indicates that Cr and Al elements form hard phases in the TiN coating, and the addition of Al elements is beneficial for the formation of Al oxides, which avoids further oxidation during the cutting process, improves the oxidation resistance of the cutters, and is conducive to increasing the cutting life of the tools. Meanwhile, the MoS? lubricating phase helps to reduce the friction coefficient of the cutters, improve the anti-wear capability of the tools, and also extends the service life of the cutters.

How to Enhance Mechanical Properties of TiN-Based Coated Cutters 6

cutting life of coated cutters

 

In summary, due to the comprehensive utilization of the advantages of various coating components in the multi-component composite coatings, they achieve better comprehensive performance, ensuring excellent wear resistance and toughness, reducing the formation of built-up edge, and possessing mechanical shock and thermal shock resistance, which can greatly improve the tool life.

 

XRD Test Analysis

XRD analysis method was used to characterize the phase structure of the CrTiAlN tool coating with the best cutting performance, and the results are shown in Figure 7. The XRD spectrum analysis indicates that the crystal phases of the coating are mainly composed of Cr, CN, CEN, and TiN at room temperature, and the amorphous phase in the coating was not detected. At the same time, high magnification scanning analysis of the tool coating revealed a large number of hard phase particles distributed on the coating surface. Combined with X-ray diffraction analysis, it is known that these hard phases are mainly CN, CrN, TiN, and AlN phases. These hard phases are beneficial for improving the cutting life of the coated cutters.

How to Enhance Mechanical Properties of TiN-Based Coated Cutters 7

Conclusion

The author has prepared TiN, TiAlN, TiN-MoS?, and CrTiAlN composite coatings using a closed-field unbalanced magnetron sputter ion plating PVD coating process. Comparative tests on the mechanical properties and cutting performance of the coatings show that:

The nanoindentation analysis obtained the nano hardness ranking of the four types of cutter coatings as follows: CrTiAlN > TiAlN > TiN > TiN-MoS?. The elastic modulus of the coatings is directly proportional to their hardness.

Under dry cutting conditions, when drilling PCNiMoVA steel, the cutting life of the coated cutters is ranked as: CrTiAlN > TiN-MoS? > TiAlN > TiN. This indicates that the cutting performance of the multi-component composite coatings is significantly better than that of the simple TiN coating, suggesting a direction for the future development of coated cutters.

Laisser un commentaire

Votre adresse de messagerie ne sera pas publiée. Les champs obligatoires sont indiqués avec *

尤物性生活午夜在线视频| 色999日韩自偷自拍美女| 内射白嫩少妇超碰| 99爱这里只有精品| 色狠狠久久av北条麻妃| 美女逼男逼小穴小骚下载| 欧美男女舔逼舔鸡巴视频| 男人扒开女人腿狂躁免费| 亚洲欧美日韩中文v在线| 啊啊好想被大鸡巴操视频| 99国产精品一区二区| 极品一区二区三区av| 黄片观看骚货浪荡| 国产色哟哟精选在线播放| 91偷自产一区二区三区蜜臀| 美女日比视频播放| 欧美后入尻逼视频| 呦交小u女国产精品99| 亚洲AV无码一区二区三区系列| 最新的亚洲欧美中文字幕| 国产一二三四五自产| 国产中文字幕在线一区二区三区| 操逼操的翻白眼视频| 黄色软件大屌怒戳粉嫩小穴| 精品久久久久亚洲中文字幕| 大鸡巴日小美女明星的BB| 日本美女阴户射尿| 国产一区二区在线观看精品| 国产精品亚洲一区二区三区下载| 性一乱一交一免费看视频| 男人把鸡巴插入女人| 天美传媒精品1区2区3区| 国产精品视频一区二区三区八戒| 美国大鸡巴操逼视频| 日本最新免费不卡一区二区三区| 农村胖肥胖女人操逼视频| 中文字幕亚洲精品女同一页| 国产黄片在线免费看| 最新中文字幕av不卡高清| 男生和女人靠逼视频| 国产品无码一区二区三区在线|