欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

How to select turning tool insert?in turning, especially in finishing?

Selection method of turning tool insert

1 first, determine the main deflection angle of turning tool insert

Among the main deflection angles of conventional turning tool insert, those suitable for finishing machining are generally between 90 ° and 95 °, especially 91 °, 93 ° and 95 °. The main deflection angle close to 90 ° makes the cutting force follow the axial direction of the workpiece, and no force in the vertical direction is applied to the workpiece to avoid vibration and deformation (thin-walled parts processing is particularly important). The main deflection angle is generally guaranteed on the turning tool bar.

2 determine the tool tip angle (turning tool insert shape)

Circular turning tool insert (R type), 90 degree square turning tool insert (s type), 80 degree diamond turning tool insert (C type), 80 degree convex triangular turning tool insert (W type), 60 degree triangular turning tool insert (T type), 55 degree diamond turning tool insert (D type), 35 degree diamond turning tool insert (V type). These turning tool insert shapes basically cover more than 90% of the conventional turning tool insert.

These kinds of turning tool insert are arranged in terms of turning tool insert strength: R, s, C (W), D, V.

The insert strength of R turning tool is the highest and V is the lowest. However, the higher the strength, the greater the resistance and the greater the risk of vibration. Therefore, we often choose R, s, C (W) for rough machining. For finishing, we will choose D and V. V is the best and R is the worst for the profiling capability required for finishing.

3 determine the front angle and rear angle of turning tool insert

The negative rake angle turning tool has good insert rigidity and is not easy to collapse, which is suitable for rough machining, while the positive rake angle turning tool is easy to insert and cut, which is more suitable for finishing machining. There is a matching relationship between the back angle and the front angle. Generally, the insert of the negative front angle turning tool is basically a 0 degree back angle. While the positive rake angle turning tool is inserted with three commonly used rake angle combinations (only turning) of 5 ° (B, ISO code, the same below), 7 ° (c) and 11 ° (P).

Common combinations with turning inserts

CC / CP (C-type positive rake angle turning tool is inserted into 7 ° / 11 ° rear angle), DC (D-type positive rake angle turning tool is inserted into 7 ° rear angle), VC / VB (V-type positive rake angle turning tool is inserted into 7 ° / 5 ° rear angle), WB / WC (W-type positive rake angle turning tool is inserted into 5 ° / 7 ° rear angle). These combinations are also the insert shapes of turning tools used for conventional finishing machining (the front and rear corners are determined)

According to the combination of the three, the insert form of conventional finishing turning tool is as follows:

95 ° main deflection angle turning tool bar + CC turning tool insert

93 ° main deflection angle turning tool bar + WB / WC / DC / VC / VB turning tool insert

91 ° main deflection angle turning tool bar + DC / VC / VB turning tool insert

Among them, 93 ° main deflection angle turning tool bar + DC is the best finishing scheme recommended by individuals (only for turning radial direction). This scheme allocates appropriate cutting parameters and the machining effect should be one of the best in turning at present. The roughness of 1.6 of several different materials has been tested, and the roughness of 0.8 of another steel part is limited by the diameter of the turning tool bar because it is an internal hole. Only the turning tool bar + CC turning tool with a main deflection angle of 95 ° can be inserted.

Of course, the above choice is not unique. Under the condition that the medium and large diameter solid materials can reach the high line speed, the turning tool insert with 0 ° back angle (ISO code n) can also turn out better roughness, but the roughness at this time is more “ground” by the CVD coated turning tool insert with thick alumina at the high line speed. The roughness is basically one grade different from that of the turning tool inserted and processed above. In other words, if the CN turning tool is inserted, it can be finished to 1.6, and if the DC turning tool is inserted, it can be finished to 0.8s

selection of turning tool bar for your insert

Outer diameter finishing turning tool bar

1.PDJNRAbout turning inserts: 3 steps TO MAKE A PERFECT COMBINATION WITH INSERT AND TOOL BAR 2

This kind of turning tool bar is suitable for fine turning of medium and large diameter workpieces. The modified tool bar can not only turn the outer diameter and end face, but also perform profiling and turning. It is widely used in fine turning. And the machining of shaft parts does not interfere with the center.

About turning inserts: 3 steps TO MAKE A PERFECT COMBINATION WITH INSERT AND TOOL BAR 3

2.PTGNRAbout turning inserts: 3 steps TO MAKE A PERFECT COMBINATION WITH INSERT AND TOOL BAR 4

It is suitable for finishing turning of medium and large diameter. Note that this type of turning tool bar can only be turned to the outside diameter, which is not suitable for turning the outside diameter + end face.

About turning inserts: 3 steps TO MAKE A PERFECT COMBINATION WITH INSERT AND TOOL BAR 5

3. Stgcr and sclcrAbout turning inserts: 3 steps TO MAKE A PERFECT COMBINATION WITH INSERT AND TOOL BAR 6About turning inserts: 3 steps TO MAKE A PERFECT COMBINATION WITH INSERT AND TOOL BAR 7

It is suitable for fine turning of small and medium parts, but sclcr fine turning fine shaft and stgcr are not suitable for fine turning end face.

About turning inserts: 3 steps TO MAKE A PERFECT COMBINATION WITH INSERT AND TOOL BAR 8
About turning inserts: 3 steps TO MAKE A PERFECT COMBINATION WITH INSERT AND TOOL BAR 9

4.SDJCRAbout turning inserts: 3 steps TO MAKE A PERFECT COMBINATION WITH INSERT AND TOOL BAR 7

It is applicable to finish turning of all outer diameter parts, including profiling and shaft parts. No matter how big the diameter is, it is suitable. And the cutting is light and fast, and it is more anti collapse than VB / VC turning tool insert. This knife is in hand. It’s clean and precise!

About turning inserts: 3 steps TO MAKE A PERFECT COMBINATION WITH INSERT AND TOOL BAR 11

Selection of turning tool bar for internal hole finishing machining

1.PDUNRAbout turning inserts: 3 steps TO MAKE A PERFECT COMBINATION WITH INSERT AND TOOL BAR 12

Similar to the outer diameter, the turning tool bar is suitable for finishing turning of medium and large diameter parts, and can also be used for profiling and end face processing.

About turning inserts: 3 steps TO MAKE A PERFECT COMBINATION WITH INSERT AND TOOL BAR 13

2.PTFNRà propos du tournage des plaquettes : 3 étapes POUR FAIRE UNE COMBINAISON PARFAITE AVEC LA PLAQUETTE ET LA BARRE D'OUTILS 14

Suitable for fine turning of medium and large parts.

à propos du tournage des plaquettes : 3 étapes POUR FAIRE UNE COMBINAISON PARFAITE AVEC LA PLAQUETTE ET LA BARRE D'OUTILS 15

3.SCLCRà propos du tournage des plaquettes : 3 étapes POUR FAIRE UNE COMBINAISON PARFAITE AVEC LA PLAQUETTE ET LA BARRE D'OUTILS 16

It is one of the commonly used turning tool bars for fine turning of internal holes, with a wide range of machining diameters, with a minimum of about 5.5-6.

à propos du tournage des plaquettes : 3 étapes POUR FAIRE UNE COMBINAISON PARFAITE AVEC LA PLAQUETTE ET LA BARRE D'OUTILS 17

4.STFPRà propos du tournage des plaquettes : 3 étapes POUR FAIRE UNE COMBINAISON PARFAITE AVEC LA PLAQUETTE ET LA BARRE D'OUTILS 18

Small and medium aperture is one of the commonly used turning tool bars for fine turning. Generally, the machining aperture is not more than 20-25, and the minimum is about 8-10. The cutting speed is lighter than sclcr, and the number of cutting edges inserted by the turning tool is half more than CC. It has good economy.

à propos du tournage des plaquettes : 3 étapes POUR FAIRE UNE COMBINAISON PARFAITE AVEC LA PLAQUETTE ET LA BARRE D'OUTILS 19

5.SDUCRà propos du tournage des plaquettes : 3 étapes POUR FAIRE UNE COMBINAISON PARFAITE AVEC LA PLAQUETTE ET LA BARRE D'OUTILS 20

Due to the restriction of the insert shape of the turning tool, the minimum machining diameter of this turning tool bar is about 14-16, so it is not as widely used as the previous two turning tool bars. However, because the tool tip angle is smaller than the previous two, the cutting is lighter and faster, and it can also be used for profiling.

Laisser un commentaire

Votre adresse de messagerie ne sera pas publiée. Les champs obligatoires sont indiqués avec *

欧美黑屌操B内射冒白浆| 国产午夜精品美女视频露脸| 高颜值美女视频在线观看| 亚洲国产区男人本色| 国产精品一区二区日本欧美| 人人超级碰青青精品| 久久国产精品成人18p| 国产精品视频一区二区三区分享| 国产在线麻豆精品| 97人人澡人人爽人人揉| av中文字幕一区二区精品久久| 咪咪爱一级特黄大片| 欧美一区二区三区四区五区精品| 淫荡淫水逼操烂视频| 看看美日韩操逼吧| 爆操大奶子美女视频| 冷色系的发色有哪些颜色| 大鸡吧插美女嫩逼| 日韩欧美视频在线观看不卡| 欧美精品国产一区二区在线观看| 国产操小骚逼视频| 亚洲男性天堂一区二区三区| 公交车上被后入搞逼漫画| 日本一区二区不卡在线国产| 骚女人被大吊干视‘| 国内不卡的中文字幕一区| 欧美大鸡巴操大骚逼| 精品一区二区视频在线观看| 美女大骚逼幸福遍穴| 国产熟女视频一区二区三区| 99国产精品一区二区| 久久99热人妻偷产精品| 免看一级a一片成人欧美| 免看一级a一片成人欧美| 久久精品欧美日韩精品不卡| 捆绑调教白浆一区二区三区| 日本福利一区二区视频| 免费女人男人肏逼| 最新日本一区二区三区免费看| 欧美va精品亚洲va精品| 国产精品午夜小视频观看|