欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

Este artículo presenta principalmente los métodos de instalación y procesamiento de herramientas de corte.

Grooving cutter has CNC grooving cutter, which is a tool used for cutting in mechanical manufacturing, also known as cutting tool.

The material of the knife has the following properties:

First, it has high hardness, and its normal temperature hardness is above HRC60.

Secondly, it has enough strength and toughness, enough bending strength and enough toughness to resist impact and vibration.

Third, high wear resistance. It has very high resistance to wear and can keep the blade sharp.

Fourth, high thermal hardness, which can maintain high hardness at high temperature.

Fifthly, good technology, easy to tool manufacturing and heat treatment.

According to the different equipment, the size of grooving cutter is also different. The function of slotting cutter is the same as that of many cutting tools, which is an essential cutting tool in mechanical manufacturing. Generally, it is used in some CNC lathe or CNC equipment. Of course, the use method of each slotting cutter is different. Let’s take an example.

For example, in CNC lathe slotting tool, it can not be lower than the center, the tool tip and the center of the workpiece the same height. In addition, when clamping the slotting tool, first of all, it should meet the general requirements of cylindrical turning tool clamping. The protruding part of the tool clamping on the tool holder should be as short as possible to enhance its rigidity. The number of gaskets should be as few as possible, and should be aligned with the edge of the tool holder. At least two screws should be used to compress them to prevent their vibration and produce bad use effect.

Of course, the size of slotting cutter should be consistent with the model of lathe. When the tip of the turning tool is higher than the axis of the workpiece, the actual back angle of the turning tool will be reduced, and there will be a very large friction between the back of the turning tool and the workpiece, which will shorten the tool life. If the tool tip is lower than the axis of the workpiece, the actual rake angle of the turning tool will decrease and the cutting resistance will increase. If the tool tip is not in the center, there will be a convex head when turning to the center of the end face. When using cemented carbide, if this point is ignored, turning to the center will cause the tool tip to break, so we must pay attention to it.

In addition, it is also necessary to pay special attention to that when clamping, the knife must not extend too long, and the center line of the knife must be perpendicular to the axis of the workpiece to ensure that the two secondary deflection angles are symmetrical, and the main cutting edge must be parallel to the axis of the workpiece; the bottom plane of the knife should be flat to ensure that the two secondary back angles are symmetrical. Therefore, it is very important to choose the size of slotting cutter.

Few Useful Processing Methods of Grooving and Cutting Tools 2

Installation of external groove cutter

1. When the cutting tool can meet the processing requirements, the slotting tool should not extend too long during installation.

2. The height of the main cutting edge should be controlled within the range of 0 ± 0.2mm for the center of the workpiece when the groove is turned and the cross feed is carried out, and the height of the blade and the center of the workpiece should be as high as possible.

3. The blade shall be perpendicular to the center as far as possible, and the two secondary deflection angles shall be symmetrical to ensure that the main blade is parallel to the axis of the workpiece.

Installation of cutting tool

1. During installation, the cutter should not extend too long, and the center line of the cutter must be perpendicular to the center line of the workpiece, so as to ensure the symmetry of the two secondary deflection angles.

2. When cutting a solid workpiece, the main cutting edge of the cutter must be set at the same height as the center of the workpiece, otherwise it cannot be turned to the center, and it is easy to break the cutting edge or even break the turning tool

3. The bottom plane of the cutter should be flat to ensure the turning quality.

Processing method of straight groove outside car

1. When turning low and narrow grooves, the groove turning tool with the width equal to the groove width can be used, and the one-time straight forward method can be used.

2. For the groove with accuracy requirements, the two-step straight forward method is generally adopted.

Few Useful Processing Methods of Grooving and Cutting Tools 3

Cut off method

1. Cut off the workpiece by straight forward method. The so-called straight forward method refers to cutting perpendicular to the axis of the workpiece. This method has high cutting efficiency, but it has high requirements for the grinding and installation of lathe and cutter, otherwise it is easy to break the cutter head.

2. Cut off the workpiece by the left and right knife method. In the case of insufficient cutting rigidity, the left and right tool borrowing method can be used to cut. Left and right borrowing method means that the cutter moves back and forth repeatedly in the axial direction, and then both sides feed radially until the workpiece is cut off.

3. Cut off the workpiece by reverse cutting. Reverse cutting method refers to the workpiece reverse, turning tool reverse clamping, this cutting method is suitable for larger diameter workpiece cutting.

Few Useful Processing Methods of Grooving and Cutting Tools 4
老女人爱精大鸡吧草| 我想看操小嫩逼大片| 美女日逼视频免费| 国产乱子伦视频一区二区三区| 91在线一区二区| 国产午夜福利视频第三区| 被公侵犯中文字幕在线观看| 97超级免费视频在线观看| 黄片观看骚货浪荡| 欧美人人做人人爽人人喊| 国产亚洲欧美日韩在线观看一区| 男人添女人下面免費视頻| 国产黄片在线免费看| 男人大鸡巴操女人的大逼| 天天躁久久躁中文字字幕| 亚洲国产日韩欧美高清片| 欠欠草免费在线视频| 欧美人与动人物A级| 欧美后入尻逼视频| 男人草女人的视频免费看| 大鸡巴操饿罗斯女人| 国产亚洲情侣久久精品| 久久综合色伊人九色91| 亚洲一区二区三区精品日韩| 国产高清免费一级a久久| 精品免费久久久久久久久| 高清无码精品一区二区三区| 大鸡巴狂插嫩逼视频| 大鸡巴操大屁股美女视频| 久久综合色鬼综合色| 亚洲精品一区二区精华液| 黄色三极片在线观看| 日韩成人伦理片在线观看| 精华欧美一区二区久久久| AV天堂手机福利网| 使劲操大骚逼av| 青青视频在线人视频在线| 午夜性刺激在线视频免费| 精品无码一区二区三区无码| 黑人大吊又操又添| 国产精品一区二区日本欧美|