欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

Drilling refers to the mechanical process of creating holes in solid materials using a drill bit. In general, when drilling on a drilling machine, the drill bit should perform two simultaneous movements:

Primary motion:?This involves the rotation of the drill bit around its axis (cutting motion).

Auxiliary motion:?This refers to the linear movement of the drill bit along the axis direction towards the workpiece (feed motion).

During drilling, the inherent flaws in the structure of the drill bit can, to some extent, affect the quality of the workpiece. The machining precision is generally below IT10, and the surface roughness is around Ra12.5μm, categorizing it as rough machining.

drilling holes

Drilling Operation Steps

1Marking Lines

Before drilling, familiarize yourself with the pattern requirements. Use a height gauge to mark the cross-center line at the hole position according to the dimensional requirements. The center line should be clear, accurate, and as fine as possible. After marking the lines, use a vernier caliper or a steel ruler for inspection.

2Drawing Inspection Grid or Circle

After marking the lines and ensuring they pass inspection, draw an inspection grid or circle with the hole’s center line as the symmetrical center. This serves as a reference for checking during drilling, facilitating the inspection and correction of hole positions.

3Pilot Hole Punching

After drawing the corresponding inspection grid or circle, carefully punch a pilot hole. Start with a small point, observe carefully in different directions from the cross-center line to ensure the pilot hole is at the intersection of the cross-center line. Finally, punch the pilot hole firmly, ensuring accuracy for drilling alignment.

4Clamping

Clean the machine table, fixture surface, and workpiece reference surface. Clamp the workpiece securely, ensuring a flat and stable clamping for easy observation and measurement. Pay attention to the clamping method to prevent deformation during clamping.

5Trial Drilling

It is essential to conduct a trial drill. Align the drill bit transversely with the center of the hole, drill a shallow pit at the center of the sample punched hole, visually inspect its correctness, and continuously adjust to align the pit with the inspection circle. If the deviation is small, apply force to gradually correct the position.

6Bohren

Machining the hole in metalworking generally involves manual feed operation. Once the trial broaching achieves the required positional accuracy, proceed with the broaching. During manual feeding, ensure that the feed force does not cause bending of the drill bit to prevent the hole axis from skewing.

What are the 5 Methods Available to Improve the Precision of Drilling? 1

Methods to Improve Drilling Accuracy

1Well-Sharpened Drill Bit as a Prerequisite

Before drilling, carefully select and sharpen the appropriate drill bit. The sharpened drill bit should have accurate positive rake angles, relief angles, and equal lengths for the two main cutting edges. Additionally, the two main cutting edges should be symmetrical with the centerline of the drill bit, and the main relief surfaces should be smooth. To facilitate centering and reduce wall roughness, appropriate grinding of the relief and main cutting edges is necessary (preferably rough grinding on a grinding wheel followed by fine finishing on an oilstone).

2Precise Marking as the Foundation

Accurate marking with a height gauge is fundamental. Ensure accurate dimensions, and when marking, create an angle of 40 to 60 degrees (along the marking direction) between the marking needle and the workpiece marking plane to produce clear and uniform lines. Select a well-machined reference surface for marking, ensuring its own flatness and perpendicularity to adjacent surfaces. After marking the crosshair lines for hole positions, use a center punch to mark the center point on the crosshair lines (the punch point should be small and accurately positioned) to facilitate centering during broaching.

3Correct Clamping is Key

For holes with a diameter less than 6mm, if precision is not critical, hand clamping of the workpiece for drilling is acceptable. For holes in the range of 6 to 10mm, if the workpiece is regular and flat, use a flat-nose pliers but ensure the workpiece surface is perpendicular to the drill spindle. When drilling larger diameter holes, the flat-nose pliers must be fixed with bolts. For larger workpieces with hole diameters exceeding 10mm, use a clamping method with a pressure plate for broaching.

4Accurate Centering is Crucial

After clamping the workpiece, do not rush to start drilling; instead, begin with centering. Centering can be static or dynamic. Static centering occurs before the drilling machine is started, aligning the centerline of the drill spindle with the intersection of the workpiece’s crosshair lines. While this method is safer and more convenient for beginners, it may result in lower drilling accuracy due to factors like the swing of the drill spindle. Dynamic centering is performed after the drilling machine is started, considering various uncertain factors, resulting in relatively higher accuracy.

5Thorough Inspection is Essential

Inspection helps discover the accuracy of the hole promptly, allowing necessary measures to be taken for correction. For holes requiring high accuracy, a processing technique involving drilling, reaming, and tapping is often employed. After drilling a small hole in the first step, use a caliper to measure the deviation from the center of the bottom hole to the reference surface. If the deviation is less than 0.10mm, adjustments can be made during reaming by increasing the drill bit’s rake angle and weakening the automatic centering effect, gradually pushing the workpiece in the correction direction. If the deviation exceeds 0.10mm, a round file can be used to smooth the sidewalls of the bottom hole, ensuring a smooth transition with the arc of the bottom hole.

Schreibe einen Kommentar

Deine E-Mail-Adresse wird nicht ver?ffentlicht. Erforderliche Felder sind mit * markiert.

西瓜在线看免费观看视频| 操大屌粉的小穴视频| 狠狠色伊人亚洲综合成人| 国产高清免费一级a久久| 亚洲午夜福利视频在线| 美女人的逼免费观看| 又大黄又硬又爽免费视频| 操女人b直播软件| 免费的黄片很很操| 大香蕉尹人97超级视频| 国产精品一区二区三区色噜噜| 大香蕉中码手机在线视频| 欧美日韩在线成人| 极品美女销魂一区二区三区| 被公侵犯中文字幕在线观看| 97国产精品免费一二区| 九九视频精品只有这里有| 东京热无码AV一区二区三区| 中文字幕在线观视频| 日本最新免费不卡一区二区三区| 亚洲国产一区二区不卡在线资源| 9国产亚洲精品国产| 国产a一级毛片午夜剧院| 两个人免费视频高清| 欲色福利网免费在线播放| 久久久精品亚洲Av| 99热这里有精品在线观看| 色橹橹欧美在线观看视频高清免费| 快速了解国产一级a爱片| 瓯美在线免费视频笫一区第二区| 国产精品亚洲综合av| 日韩欧美综合一二三区| 精品一二三四区中文字幕| 久久99热东京热亲亲热| 婷婷6月天丁香综合在线| 香蕉国产精品偷在线| 老司机精品成人无码AV| 一级e片在线观看| 在线 中文字幕 第一页| ai换脸久久一区二区亚洲av| 99久久久国产精品美女|