欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

In the bearing and standard parts industry, steel balls and screws are produced using highly efficient automatic cold heading machines. These machines have high production rates, but for medium and large-sized steel balls, the life and efficiency of the matching alloy steel dies are reduced due to the following factors during the cold heading process:

Wear and deformation caused by the intense flow of the deformed metal on the die surface. Sometimes, the die cavity surface is scratched, abraded, or even adhered to, which easily causes dimensional errors and scrapping of the die, resulting in poor product quality.

The die cavity is easily deformed due to the relatively insufficient yield strength of the matrix material.

After continuous and repeated stress, especially in areas with stress concentration, the fatigue life of the alloy steel is relatively low, leading to fatigue failure as the number of heading operations increases.

Therefore, in addition to further improving the life of alloy steel dies, there is a widespread demand for a new material that is both wear-resistant and has good toughness to adapt to the development of the cold heading industry.

Test Results and Application Assessment

To expand the application field of cemented carbide and meet the urgent demand of steel ball factories for large-sized steel ball cemented carbide dies, based on our long-term work experience and domestic and foreign data collection, we finally selected a specially made coarse-grained WC powder, supplemented by an appropriate binder phase, to formulate YGC-I and YGC-Ⅱ coarse-grained cemented carbides (YGC-Ⅱ has a higher binder phase content than YGC-I). The conventional performance data of YGC-I and YGC-Ⅱ are shown in Table 1.

An Application of Coarse-Grained Cemented Carbide in Cold Heading Dies for Steel Balls 2

To study the effect of different particle sizes of WC powder on the fracture toughness of cemented carbide, fine-grained cemented carbide YG10X, medium-coarse grained cemented carbide YG18C, and YG20C were also prepared.

The fracture toughness of fine-grained, medium-coarse grained, and super-coarse grained cemented carbides with three different WC particle sizes was measured, and the results are shown in Table 2. It can be observed from Table 2 that as the WC particle size changes from fine-grained to medium-coarse grained and then to coarse grained, the fracture toughness of the alloy increases significantly, or even doubles. Even within the same particle size range, the fracture toughness of the alloy also increases with the increase of the binder phase content. This indicates that there are two ways to improve the fracture toughness of the alloy: first, by selecting coarse-grained WC powder, and second, by increasing the binder phase content of the alloy.

An Application of Coarse-Grained Cemented Carbide in Cold Heading Dies for Steel Balls 3

carbide material for cold heading

Selected YGC-I and YG10X samples were used to take scanning electron microscopy (SEM) fracture photos. Figure 1a shows the SEM fracture photo of YGC-I, and Figure 1b shows the SEM fracture photo of YG10X. Careful observation of the SEM fracture photos reveals that YGC-I has coarse grains and a thick binder phase layer, with cracks extending along the binder phase, resulting in mostly intergranular fractures and thus a higher fracture toughness K?C. In contrast, YG10X has very fine grains and a very thin binder phase layer, with mostly transgranular fractures, leading to a lower fracture toughness K?C. This indicates that the trend in fracture toughness values of carbides with different grain sizes is consistent with the conclusions drawn from the analysis of SEM fracture photos.

The aforementioned coarse-grained cemented carbide developed was applied to cold heading larger specification steel balls φ17.4625 and φ19.05. After being used on a Z32-28 machine at a certain factory, the usage data show that the coarse-grained cemented carbide is capable of stamping larger specification steel balls, and its die core life is more than 8 to 10 times longer than that of GCr15. This not only expands the application scope of cemented carbide but also provides the possibility for the bearing industry and standard parts industry to adopt carbide dies with larger heading forces. Moreover, due to the significant increase in die life, it brings about considerable economic benefits.

???????

1.Selecting specially made coarse-grained WC powder and correspondingly increasing the binder phase content of the alloy is an effective way to improve the fracture toughness of cemented carbide.

2.SEM fracture analysis indicates that coarse-grained cemented carbide fractures are mostly intergranular, resulting in a higher fracture toughness K?C, while fine-grained cemented carbide fractures are mostly transgranular, leading to a lower fracture toughness K?C.

3.The usage results show that the life of coarse-grained cemented carbide die cores is more than 8 to 10 times longer than that of GCr15.

4.In summary, for the stamping of larger specification steel balls, choosing coarse-grained cemented carbide is a reasonable option.

???? ???????

?? ??? ??? ????? ????? ??????????. ?????? ????????? ???? ????? ?? *

中文字幕你懂的av一区二区| 九九视频精品只有这里有| 国产日女人视频在线观看| 上萬網友分享a级国产乱| 九九视频这里只有精品| 日韩欧美视频在线观看不卡| 男人草女人的视频免费看| 亚洲国产精品伦理在线看| 美国大骚逼啊啊啊| 猛哥操女人B视频| 神马我不卡手机在线观看| 在线 中文字幕 第一页| 免费看澡美女逼视频看看| 亚洲综合一区国产精品| 男女真人牲交高潮全过程| 九九在线精品亚洲国产| 猛插女人小穴视频| 大鸡巴操饿罗斯女人| 中国熟女色av夜夜嗨| 骚狐狸免费在线观看视频| 久久高清中文字幕第一页| 亚洲 欧美 精品 高清| 国产一区精品在线| 麻豆视频一级片在线观看| 国产伦精品一区二区三区视频抖音| 午夜性无码视频在线播放| 欧洲老妇人操大逼| 国产裸模大尺度私拍视频| 大鸡巴操逼 公司| 大玩具猛插大bb| 欧美老熟妇又粗又大| 黄色高清带三级1集2集| 国产欧美一区二区精品久久久| 国产亚洲欧美中文日韩| 亚洲狠狠插狠狠搞狠狠摸| 老太太在丛林日老B| 欧美高清一二三区| 午夜场射精嗯嗯啊啊视频| 粗大长内射女人视频| 欧美99热这里都是精品| 亚洲卡通动漫第127页|